manualshive.com logo in svg

allen BDF6048B, Safety & Operation Manual, Page: 36 / 42

Share
Download
allen BDF6048B Safety & Operation Manual Download Page 36

053016

Page 36

SECTION 3

OPERATION

Section 3

Lubrication Maintenance

LUBRICATION SCHEDULE

Reversing Valve Slide 

Bracket

Lubricate

NLGI-2 Lithium Base Grease - Lubricate slowly until excess lubricant is observed, approximately 

5-6 pumps . 

Hydraulic Oil Reservoir

Inspect

68 Hydraulic Oil - Add hydraulic oil if necessary. Replace oil filter with a 10μm filter element after 

the first 50 hours and every 250 hours thereafter. 

Engine Crankcase

Inspect

Replace oil filter with a 10 micron filter element after the first 50 hours and every 250 hours 

thereafter .

LEGS & TRAVEL BOGIES

Power Leg Screws

Lubricate

NLGI-2 Lithium Base Grease - Lubricate slowly until excess lubricant is observed, approximately 

5-6 pumps . 

Bogie Wheels

Lubricate

NLGI-2 Lithium Base Grease - Extend Inner Leg 5 Inches. Apply 5 to 10 pumps of grease. Retract 

leg to its original position .

CONTROLLER

Controller Cam Rollers

Lubricate

Engine Oil SAE 30, MS SD or SE

Controller Sliding Parts

Lubricate

L88023 “Anti-seez” or graphite filled grease. - Brush L88023 “Anti-seez” around slots and on 

main controller rail and striker arms. Apply to finishing roller reversing rod.

Idler Sprocket Bearings

Lubricate

NLGI-2 Lithium Base Grease - Lubricate slowly until excess lubricant is observed.

EVERY 25 HOURS

POWER UNIT

Engine Crankcase

Replace

Engine Oil SAE 30, MS SD or SE - Add oil if necessary .

PAVING CARRIAGE

Engine Crankcase

Replace

Engine Oil SAE 30, MS SD or SE - Add oil if necessary .

LEGS & TRAVEL BOGIES

Drive Bogie Axle Bearings

Lubricate

NLGI-2 Lithium Base Grease - Lubricate slowly until excess lubricant is observed.

Bogie Drive Chains

Lubricate

Chain Lube

CONTROLLER

Carriage Travel Chains

Lubricate

Chain Lube

AS REQUIRED (AT LEAST ONCE A YEAR)

POWER UNIT

Hydraulic Oil Reservoir

Replace

68 Hydraulic Oil - Remove and clean suction screen . Replace oil filter element with a 10 micron 

element every 300 hours .

PAVING CARRIAGE

Hydraulic Oil Reservoir

Replace

68 Hydraulic Oil -Remove and clean suction screen . Replace oil filter element with a 10 micron 

element every 300 hours .

LEGS & TRAVEL BOGIES

Manual Leg Screws

Lubricate

NLGI-2 Lithium Base Grease - Disassemble leg and brush grease onto leg screw and fill leg 

thrust bearing with grease .

Leg Rollers

Lubricate

NLGI-2 Lithium Base Grease - Remove leg rollers and work grease into bearings .

Summary of Contents for BDF6048B











































Reviews:

No comments