manualshive.com logo in svg

allen BDF6048B, Safety & Operation Manual, Page: 20 / 42

Share
Download
allen BDF6048B Safety & Operation Manual Download Page 20

053016

Page 20

SECTION 3

OPERATION

Section 3

36’ to 48’ Machine

84’ to 108’ Machine

PICTURE 1

WARNING

• 

Please use extreme caution when lifting the BDF. Make 

sure crane or lifting equipment has enough capacity 
to lift the weight of the machine . Please make sure all 
lifting apparatus, straps & cables are free from structural 
damage and are rated for the proper lifting capacity .

•  Please make sure all ground personnel are clear of 

danger while the machine is being lifted .

•  LOCK

 all (4) legs prior to lifting the machine as they could 

roll causing an unbalanced load and personal injury .

•  ALLOWING

 the weight of the machine to rest on the 

carriage paving rollers

 WILL

 cause damage to the 

carriage or the paving rollers, 

ALWAYS

 place blocks 

under end-frame

•  ALWAYS

 attach 

LONG

 safety ropes or tag lines to the 

ends of the machine prior to lifting .

•  Position the paving carriage opposite the power unit end 

to provide a balance lift for the machine .

•  Lifting straps are provided . Please be aware of the lifting 

capacity for all straps .

•  Lifting angles should not be less than 45° from horizontal . 

SEE PICTURE 1 BELOW

•  If using a center cable, 

CAUTION

 should be taken when 

adjusting the length . 

When Lifting Your Machine

Summary of Contents for BDF6048B











































Reviews:

No comments