manualshive.com logo in svg

Allen-Bradley POINT I/O 1734-OE2C, Installation Instructions Manual, Page: 20 / 22

Share
Download
Allen-Bradley POINT I/O 1734-OE2C Installation Instructions Manual Download Page 20

20

    POINT I/O 2 Current Output and 2 Voltage Output Analog Modules 

Publication 1734-IN002E-EN-E - October 2016

Enclosure Type Rating

None (open-style)

Wire Size

0.25... 2.5 mm

2

 (22...14 AWG) solid or stranded copper wire rated at 

75 °C (167 °F) or greater 1.2 mm (3/64 in.) insulation max

Wire Category

(1)

1 - on signal ports

Terminal Base Screw Torque

0.6 Nm (7 lb-in)

Weight, approx

36 g (1.27 oz)

North American temp code

T4A

IEC temp code

T4

(1)

Use this Conductor Category information for planning conductor routing. Refer to Industrial Automation Wiring and 
Grounding Guidelines, publication 

1770-4.1

.

Environmental Specifications

Attribute

1734-OE2C

1734-OE2V

Operational Temperature

IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20…55 °C (-4…131 °F)

Temperature, surrounding air, 
max

55 °C (131 °F)

Storage Temperature

IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock):
-40…85 °C (-40…185 °F)

Relative Humidity

IEC 60068-2-30 
(Test Db, Unpackaged Nonoperating Damp Heat):
5…95% noncondensing

Vibration

IEC60068-2-6 (Test Fc, Operating)
5 g @ 10...500 Hz

Shock
   Operating
   Non-Operating

IEC 60068-2-27 (Test Ea, Unpackaged Shock)
30 g 
50 g 

Emissions

CISPR 11: Group 1, Class A

ESD Immunity

IEC6100-4-2
6 kV contact discharges
8 kV air discharges

General Specifications

Attribute

1734-OE2C

1734-OE2V

Summary of Contents for POINT I/O 1734-OE2C























Reviews:

No comments