manualshive.com logo in svg

Allen-Bradley 1779-KFM, User Manual, Page: 173 / 211

Share
Download
Allen-Bradley 1779-KFM User Manual Download Page 173

PAD Message Set

Chapter 11

116

corresponding reply packets.  The STS value is either 00 to indicate a
successful transaction completion or a non-zero value to indicate an error.

If you initiate a series of PAD command packets without waiting for each
reply, there is no guarantee that the command packets will be delivered at
the destination in the same order in which you sent them.  To guarantee
order of delivery, wait for each reply before sending the next command
packet.

A host computer for a 1779-KFM interface can send PAD messages to
and receive PAD messages from a host device for a 1779-KFL or
1779-KFM interface at another Data Highway II station.  The host device
at the other station could be a dumb terminal, a robot, or a computer.

Figure 11.2 shows a PAD-mode data frame containing a PAD packet.  The
PAD packet can contain a maximum of 256 bytes of application data in
any format.  However, if the destination-station interface is in the Native
mode, the PAD packet must be limited to a maximum of 
238 bytes.

Figure 11.2

PAD Format in PAD Mode

DATA (Any Format)

256 Bytes Max.

DATA

(From Preceding Layer)

CTL

ADDR

FCS

FLG

Application Fields

FLG

HDLC DataLink Fields

The format of all PAD-mode PAD messages is exactly as shown in
Figure 11.2.  There is no provision for replies to confirm delivery of
messages to their destinations.

The PAD-mode format has no provision for specifying the destination
station for PAD messages.  The destination station must be established
beforehand through station-management commands.

Packet Format for PAD Mode

Using PADMode PAD Messages

Summary of Contents for 1779-KFM




















































































































































































































Reviews:

No comments