Allen-Bradley 1606-XLC Reference Manual Download Page 14

All parameters are specified at 48V, 10A, 230Vac, 25°C ambient and after a 5 minutes run-in time, unless noted otherwise.

14

Rockwell Automation Publication 1606-RM043A-EN-P — March 2014

Bulletin 1606 Switched Mode Power Supplies

 

Switching Frequencies 

The power supply has two converters with two different switching frequencies included. 

Switching frequency 1 

70kHz to 130kHz 

PFC converter, input voltage and output power dependent 

Switching frequency 2 

80kHz to 140kHz 

Main converter, output power dependent 

 

 

15. Environment 

 

Operational temperature

*)

 

-25°C to +70°C (-13°F to 158°F) 

reduce output power according Fig. 15-1

 

Storage temperature 

-40 to +85°C  (-40°F to 185°F) 

for storage and transportation 

Output de-rating 

6.4W/°C 
12W/°C 

45°C to 60°C (113°F to 140°F) 
60°C to 70°C (140°F to 158°F) 

Humidity

 **)

 

5 to 95% r.h. 

IEC 60068-2-30 

Vibration sinusoidal 

2-17.8Hz: ±1.6mm; 17.8-500Hz: 2g

***)

 

2 hours / axis 

IEC 60068-2-6 

Shock 

30g 6ms, 20g 11ms

***)

 

3 bumps / direction, 18 bumps in total 

IEC 60068-2-27 

Altitude 

0 to 2000m  (0 to 6 560ft) 

without any restrictions 

 

2000 to 6000m  (6 560 to 20 000ft) 

reduce output power or ambient temperature, 
see Fig. 15-2 
IEC 62103, EN 50178, overvoltage category II 

Altitude de-rating 

30W/1000m or 5°C/1000m 

> 2000m (6500ft), see Fig. 15-2

 

Over-voltage category 

III 

IEC 62103, EN 50178, altitudes up to 2000m  

 

II 

altitudes from 2000m to 6000m 

Degree of pollution 

IEC 62103, EN 50178, not conductive 

LABS compatibility 

The unit does not release any silicone or other LABS-critical substances and is suitable for 
use in paint shops. 

Audible noise 

At load currents below 1A some audible noise will be emitted from the power supply 

*)   Operational temperature is the same as the ambient temperature and is defined as the air temperature 2cm below the unit. 
**)   Do not energize in the presence of condensation. 
***) Higher levels allowed when using the 1606-XLC wall mounting bracket.

 

 

Fig. 15-1

   Output current vs. ambient temp. 

 

Fig. 15-2

   Output current vs. altitude 

 

Allowed Output Current at 48V

0

-25

0

20

40

70°C

2A

4A

6A

8A

10A

12A

60

B

A

Ambient Temperature

A...100 to 264Vac, continuous
B... 85Vac, continuous
C... Short term

C

 

0

0

2000m

4000m

6000m

2A

4A

6A

8A

10A

12A

B

A

C

A... Tamb < 60°C

B... Tamb < 50°C

C... Tamb < 40°C

D... Short term

D

Allowable Output Current at 48V

Altitude

 

See section 3 for derating requirements for input voltages between 85Vac and 100Vac. 

 

Summary of Contents for 1606-XLC



























Reviews: