ALLEN & HEATH XONE:DB4 User Manual Download Page 41

Page: 41 / 44

Allen & Heath

XONE:DB4 User Guide

SPECIFICATIONS

Dimensions and Weights

The console is fitted with rubber feet for desktop operation. A screw on rack ear kit is avail-
able for 19” rack or plinth mounting.

Width

Height

Depth

Weight

Desktop

320 mm (12.6”) 88 mm (3.5”) 358 mm (14”) 5.1 kg (11 lbs)

Rack ears fitted 483 mm (19”) 88 mm (3.5”) 358 mm (14”)

Packed

530 mm (20.9”) 470 mm (18.5”) 260 mm (10.2”) 8.6 kg (19 lbs)

To order a rack ear kit for the XONE:DB4, please quote the part number X:DB4-RK19.

Operating levels

Main outputs

0VU = +4dBu

Monitor

0VU = +4dBu

Record

0VU = +4dBu

Maximum output level

+16dBu balanced

Mic Sensitivity

-20dB - -50dB

RIAA input sensitivity 1kHz

70mV = 0VU (200mV max)

Frequency response Line in to Mix out

10Hz - 20kHz +0/-0.5dB

Distortion at 1kHz Line in at +0Vu out

0.003% (-90dB) un-weighted

Main Mix noise 22Hz— 22KHz un-weighted

-88dBu (104dB dynamic range)

Residual Mix noise22Hz— 22KHz un-weighted

-94dBu

Equalization

+6dB boost/-26dB or Total Kill 3 Band

Fader Shutoff

-110dBr

See Page 40 for Digital Architecture Specification

Summary of Contents for XONE:DB4













































Search results

Summary of Contents for XONE:DB4

Reviews:

Related manuals for XONE:DB4

Brands by name

Popular brands

ALLEN & HEATH XONE:DB4, User Manual

Search results

Summary of Contents for XONE:DB4

Reviews:

Related manuals for XONE:DB4

Brands by name

Popular brands