background image

Olympus Series / Automated Standalone Asynchronous CD/DVD Duplication System / User Manual 

Overview 

Before you start using this system, please read the following to ensure proper operation: 

DVD Duplication Limitations 

The  DVD  system  will  not  copy  any DVDs that have Copy Protection encoded in the 
content.  Typically,  most  DVDs  you  purchase  or  rent  from  a  store,  contain  Copy 
Protection.  
In  addition  to  the  copy  protection  limitation,  the  autoloader  will  only  copy  a  DVD5 
format (4.7 GB) disc to another DVD5 format recordable DVD media. If your autoloader 
has  double  layer/dual  layer  capability,  you  can  copy  a DVD9 format (8.5 GB) disc to 
another DVD9 format recordable DVD media, but you cannot duplicate a DVD5 format 
disc  on  to  a  DVD9  format  recordable  media or vice versa without enabling this feature 
first.  

Temperature Warning 

If the system was stored in a location where the temperature dropped below 32° F (0° C) 
within the past 24 hours, leave the autoloader in a warm room with temperatures at least 
65°  F (19° C) for four hours prior to powering it on for the first time. Failure to do so 
may cause irreparable harm and prevent the autoloader from functioning.  

Maintenance 

It is very important to operate and keep the autoloader in a dust free, clean environment 
since  dust  is  the  number  one  killer  of CD/DVD recording devices. Failure to do so can 
severely  damage  your  autoloader.  We  strongly  suggest  that  you  constantly  use an Air 
Duster (Canned Air) to clear off any dust on the surface of the autoloader.  

 
Note:

 Do not try to use an Air Duster to clean the autoloader while the writer trays are 

open. In doing so, you may inadvertently blow dust into the recording device and damage 
it.  
 
 
 
 
 

Summary of Contents for Olympus series

















Reviews: