manualshive.com logo in svg

ALFAtron MUH88E, User Manual

Share
Download
ALFAtron MUH88E User Manual Download Page 29

MUH88E Kit 4K Home Distribution Hub                                                   

 

 

Alfatron.co.za

 

following figure). Set the network segment of the Matrix Switcher to the same as the 
router’s, then PCs within the LAN are able to control the Matrix Switcher. 

 

Follow these steps to connect the devices: 

Step1. 

Connect the TCP/IP port of the Matrix Switcher to Ethernet port of PC with 
twisted pair. 

Step2. 

Set the PC’s network segment to the same as the Matrix Switcher’s. Do 
please remember the PC’s original network segment. 

Step3. 

Set the Matrix Switcher’s network segment to the same as the router. 

Step4. 

Set the PC’s network segment to the original ones. 

Step5. 

Connect the Matrix Switcher and PC(s) to the router. PC(s) within the LAN is 
able to control the Matrix Switcher asynchronously. 

Then it’s able to control the device via GUI. 

 

GUI for TCP/IP control 

MUH88E Kit provides with built-in GUI for convenient TCP/IP control. GUI allows users 
to interact with MUH88E Kit through graphical icons and visual indicators. 

Type 192.168.0.178 in your browser, it will enter the log-in interface shown as below: 

Router

Internet

PC

TCP IP Port

/

Summary of Contents for MUH88E














































Reviews:

No comments

Brands by name

Popular brands

Load more brands