manualshive.com logo in svg

ALFAtron MUH88E, User Manual

Share
Download
ALFAtron MUH88E User Manual Download Page 28

MUH88E Kit 4K Home Distribution Hub                                                   

 

 

Alfatron.co.za

 

4.4 

TCP/IP Control 

Besides IR control, RS232 control, the Matrix Switcher boasts option TCP/IP port for IP 
control. 

Default settings: IP: 192.168.0.178; Subnet Mast: 255.255.255.0; Gateway: 
192.168.0.1; Serial Port: 4001.   

IP& gateway can be changed as you need, Serial Port cannot be changed. 

Connect the Ethernet port of control device and TCP/IP port of the Matrix Switcher, and 
set same network segment for the 2 devices, users are able to control the device via 
web-based GUI or designed TCP/IP communication software. 

 

Control Modes 

The Matrix Switcher can be controlled by PC without Ethernet access or PC(s) within a 
LAN. 

 

Controlled by PC 

Connect a computer to the TCP/IP port of the Matrix Switcher, and set its network 
segment to the same as the Matrix Switcher’s.

 

 

 

Controlled by PC(s) in LAN 

Connect the Matrix Switcher, a router and several PCs to setup a LAN (as shown in the 

Same network 
segment as 
the switcher 

Summary of Contents for MUH88E














































Reviews:

No comments

Brands by name

Popular brands

Load more brands