manualshive.com logo in svg

Alfa level LKH UltraPure-10, Instruction Manual

Share
Download
Alfa level LKH UltraPure-10 Instruction Manual Download Page 19

5 Maintenance

Maintain the pump carefully. Study the instructions carefully and pay special attention to the warnings!
Always keep spare shaft seals and rubber seals in stock.
See separate motor instructions.

Shaft seal

Rubber seals

Motor bearings

Preventive maintenance

Replace after 12 months:
(one-shift) Complete shaft seal

Replace when replacing the
shaft seal

Maintenance after leakage
(leakage normally starts slowly)

Replace at the end of the
day: Complete shaft seal

Replace when replacing the
shaft seal

Planned maintenance

-

Regular inspection for
leakage and smooth
operation

-

Keep a record of the pump

-

Use the statistics for
planning of inspections

Replace after leakage:
Complete shaft seal

Replace when replacing the
shaft seal

Yearly inspection is
recommended
-

Replace complete bearing
if worn

-

Ensure that the bearing is
axially locked (See motor
instructions)

Lubrication

Before fitting
Lubricate the Quad-/O-rings
with silicone grease or silicone
oil

Before fitting
Silicone grease or silicone oil

See section 6.2 Relubrication
intervals

Pre-use check

CAUTION!
Fit the electrical connections correctly if they have been removed from the motor during service. (See 3.3 Pre-use check).

Pay special attention to warnings!
1. Start and stop the motor momentarily.
2. Ensure that the pump operates smoothly.

19

Summary of Contents for LKH UltraPure-10















































Reviews:

No comments

Brands by name

Popular brands

Load more brands