manualshive.com logo in svg

Alfa level LKH UltraPure-10, Instruction Manual

Share
Download
Alfa level LKH UltraPure-10 Instruction Manual Download Page 18

5 Maintenance

Maintain the pump carefully. Study the instructions carefully and pay special attention to the warnings!
Always keep spare shaft seals and rubber seals in stock.
See separate motor instructions.

5.1

General maintenance

Step 1

Always read the technical data thoroughly. (See chaper 6 Technical data)

Always disconnect the power supply when servicing the pump.

NOTE
All scrap must be stored/disposed of in accordance with current rules/directives.

Step 2

Never service the pump when it is hot.

Danger of burns!

3007-0015

Step 3

Never service the pump with pump and pipelines under pressure.

CAUTION
Fit the electrical connections correctly if they have been removed
from the motor during service.

Pay special attention to the warnings!

Atmospheric
pressure required!

3007-0019

Step 4
Recommended spare parts:
Order service kits from the service kits list
(see chapter 7 Parts list and service kits).

Ordering spare parts
Contact your local Alfa Laval sales company.

Note:
If the pump is supplied with FEP O-rings. Alfa Laval recommends that the casing O-ring is replaced during pump maintenance.

18

Summary of Contents for LKH UltraPure-10















































Reviews:

No comments

Brands by name

Popular brands

Load more brands