background image

13

Test the reversing sensitivity

For the sake of safety, it is very important to test the reversing sensitivity as soon as the control board set is 

finished.

The reversing sensitivity adjustment is inverse correlation with stall force adjustment in potentiometer A and 

B. In other word, the stall force level is higher; the reversing sensitivity level is lower.

Put an immobile object along the gate path, and then operate the gate to strike it during the open and close 

cycles. The gate must reverse as soon as object is struck with it. If the gate doesn’

t reverse, please increase 

the reversing sensitivity by turning the potentiometer A in counter-clockwise direction. (Turning the stall force 

potentiometer toward to MIN position to increase the reversing sensitivity)

Note 1: If the sensitivity setting is too higher, the gate will stop or reverses very easy by itself while 

there is little obstruction or resistance such as strong wind or heavy snow sometimes.

Note 2: Always check the gate reversing function every each time of control board set or restart after 

power off.

How to learn or erase the remote

Learn the remote

Press and release the learn button, the 

LEARN LED

light will be on, then press the key in the remote twice

in 2 seconds, the 

LEARN LED

 light will flash for 4 

seconds. Now the remote has been learnt successfully.

This control board can learn up to six remotes , if you 

want to learn more, we recommend that you buy the external receiver

LM138

.

Erase all the remote codes

Press and hold the learn button until the 

LEARN

 light is off. Now all remote codes have been erased.

How to use the remote to control the operator

Key A 

is used to operate the operator to work alternately (open-stop-close-stop-open).

When the Pedestrian Mode function is enabled, 

Key B

 is used to achieve the

Pedestrian Mode function (open the gate for the pre-setting time). When the

Pedestrian Mode function is disabled, the operator works alternately (open-stop

-close-stop-open) by pressing 

Key B

.

Summary of Contents for AC 1500

















Reviews: