ALDI Workzone Titanium+ 52299 User Manual Download

Page: 4 / 38

3500W Digital Inverter with Pure Sine Wave

AFTER SALES SUPPORT

e-mail: [email protected]

1800 909 909

MODEL: №. INF3800A • 03/2016 • 52299

(toll free)

Pack contents / parts

Congratulations on the purchase of your Workzone® Titanium 3500W Inverter

Generator with Pure Sine Wave. When you open your packaging, first remove all items

and check there are no parts damaged or missing. If you find anything wrong, do not

operate the product until the parts have been replaced or the fault has been rectified.

Failure to do so could result in serious personal injury.

NOTE:

This is a 4 stroke Inverter Generator.

The engine MUST be filled with 600ml of SAE 10W-30

BEFORE

starting.

Fresh unleaded fuel must be used in this unit. Do NOT use Ethanol based fuels.

Do NOT mix oil with fuel.

NOTE:

First time users or inexperienced operators pay particular attention to

the operation of the Generator, including details of starting and stopping and

correct use of the Generator on pages 19-23, as well as the maintenance

instructions on pages 26-31.

Intended use of the 3500W Inverter Generator with Pure Sine Wave
NOTE:

This product is for private domestic DIY use only.

It is not suitable for commercial or trade use.
This product is suited for home, camping and caravan applications & domestic house

hold mains failure back up. It will allow you to power outdoor lights, power tools,

home appliances including sensitive electronic equipment, including televisions

and computers.

NOTE:

For sensitive equipment like computers, sound systems, televisions,

microwaves etc, it is highly recommended to have a surge protector connected

to the generator.

NOTE:

This petrol Generator is NOT suitable for:

* Marine applications, and should never be used on board water craft

* Continuous off the grid power

Contents of carton

1 x 3500W Inverter Generator
1 x Instruction Manual
1 x Warranty Card & details
1 x Quick Start Guide
1 x 10mm Tube Spanner
1 x 21mm Spark Plug Tube Spanner
1 x Multi Size Spanner

1 x Double Ended Screwdriver (Phillips and flat)
2 x Wheels (+ 2 x assembly bolts, nuts, spring

washer & flat washer)

4 x Feet (+ 4 x assembly hex head screws, nuts,

spring washer & flat washer)

1 x Wheel Foot (+ 1 x assembly hex head screw)
1 x Handle Assembly (+ 2 x assembly screws

& nyloc nuts)

Summary of Contents for Workzone Titanium+ 52299







































Search results

Summary of Contents for Workzone Titanium+ 52299

Reviews:

Related manuals for Workzone Titanium+ 52299

Brands by name

Popular brands

ALDI Workzone Titanium+ 52299, User Manual

Search results

Summary of Contents for Workzone Titanium+ 52299

Reviews:

Related manuals for Workzone Titanium+ 52299

Brands by name

Popular brands