Alcatel-Lucent OmniSwitch 6850E Series Hardware User'S Manual Download Page 101 | Manualshive

Page: 101 / 182

background image

OmniSwitch Backup Power Shelf/System (BPS)

Power Supplies

OmniSwitch Backup Power Shelf/System (BPS)

January 2013

page 4-13

Power Supplies

OmniSwitch Backup Power Shelf/System (BPS) power supplies are located at the front of the chassis.
Refer to

page 4-2

for more information on component locations. Two system power supply bays and three

PoE power supply bays are provided.

Note.

For PoE installations, a minimum of one system power supply and one PoE power supply are

required to power up a single OS-BPS.

Please note that the power supplies do not provide an on/off switch. Connecting an installed power supply
to a power source will power on the power supply. Likewise, disconnecting all installed power supplies
from a power source will power off the chassis.

AC Power Supply

AC Power Supply Front Panel

Model

OS-BPS-S (OS-PS-450W-A)

Input Voltage Range

100-240VAC, 50-60Hz

Nominal Voltage

115 VAC; 230 VAC

Max. Power

450W

Input Current

8A (100-132V); 4A (180-264V)

Output Rating

12V@37A

Operating Temperature

0°C to 50°C

Storage Temperature

-40°C to +70°C

Humidity (Operating)

5% to 95% non-condensing

Humidity (Non-Operating)

5% to 95% non-condensing

Airflow

This power supply provides front-to-back airflow only for
OS-BPS applications. See

“Airflow Recommendations” on

page 4-6

for more information.

Status LED

AC Connector

Handle

Air Vent

Lock Tab

«
...
99
100
101
102
103
...
»

Summary of Contents for OmniSwitch 6850E Series























































































































































































Reviews:

No comments

Related manuals for OmniSwitch 6850E Series

Brand: Habitat Pages: 48

Brand: 3xLogic Pages: 2

SMART NODE 4950-NCE

Brand: Patton electronics Pages: 8

NetLink 2960 RAS

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 2

Brand: Qlogic Pages: 20

Brand: Lanner Pages: 2

Brand: process-informatik Pages: 8

4-Port 10/100Mbps Ethernet Broadband Router

Brand: AOpen Pages: 41

Brand: Radicom Pages: 27

Speedway Revolution

Brand: impinj Pages: 60

Hotwire 8775 MSDSL

Brand: Paradyne Pages: 10

Brand: Xyclop Pages: 144

Brand: Silvertel Pages: 9

Elinx EIR508 Series

Brand: B&B Electronics Pages: 2

Brand: Symantec Pages: 100

CyberSWITCH CSX101

Brand: Cabletron Systems Pages: 72

Brand: B+B SmartWorx Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands