Alcatel-Lucent OmniSwitch 6850E Series Hardware User'S Manual Download Page 112

Page: 112 / 182

Disconnecting a Chassis from the OS-BPS

OmniSwitch Backup Power Shelf/System (BPS)

page 4-24

OmniSwitch Backup Power Shelf/System (BPS)

January 2013

Removing PoE Power Supplies

When removing a power supply, first disconnect the power cord from the power source. Once the

power cord is disconnected, pull the power cord out of the power supply housing.

Pressing the lock tab toward the right, as shown, will free the lever. Pull the lever to release the power

supply from chassis, pull the power supply straight back and out of the chassis slot.

Note.

If you are not replacing the power supply, be sure to install a blank cover panel over the empty

power supply bay.

Lock Tab

Summary of Contents for OmniSwitch 6850E Series























































































































































































Search results

Summary of Contents for OmniSwitch 6850E Series

Reviews:

Related manuals for OmniSwitch 6850E Series

Brands by name

Popular brands

Alcatel-Lucent OmniSwitch 6850E Series, Hardware User'S Manual

Search results

Summary of Contents for OmniSwitch 6850E Series

Reviews:

Related manuals for OmniSwitch 6850E Series

Brands by name

Popular brands