Alcatel-Lucent OmniSwitch 6850E Series Hardware User'S Manual Download Page 99

Page: 99 / 182

OmniSwitch Backup Power Shelf/System (BPS)

Rack-Mounting

OmniSwitch Backup Power Shelf/System (BPS)

January 2013

page 4-11

Mid-Mounting the Chassis In the Rack

The chassis may also be installed in the rack using mid-mount flanges. To mid-mount the chassis in a
rack, follow the steps below.

If applicable, remove the factory-installed front mounting plate and slot rails from the side of the

chassis by loosening and removing the attachment screws.

Install the individual mounting brackets at the midpoint of the chassis using the four threaded holes on

each side.

Mark the holes on the rack where the chassis is to be installed.

One person should lift and position the chassis until the mid-mount flanges are flush with the rack post.

Align the holes in the flanges with the rack holes marked in step 3.

Remove

Summary of Contents for OmniSwitch 6850E Series























































































































































































Search results

Summary of Contents for OmniSwitch 6850E Series

Reviews:

Related manuals for OmniSwitch 6850E Series

Brands by name

Popular brands

Alcatel-Lucent OmniSwitch 6850E Series, Hardware User'S Manual

Search results

Summary of Contents for OmniSwitch 6850E Series

Reviews:

Related manuals for OmniSwitch 6850E Series

Brands by name

Popular brands