background image

12

OAW-AP228 Wireless Access Point

| Installation Guide

Safety and Regulatory Compliance

Alcatel-Lucent provides a multi-language document that contains country-specific restrictions and 

additional safety and regulatory information for all Alcatel-Lucent access points. This document can 

be viewed or downloaded from the following location: 

www.alcatel-lucent.com/enterprise 

Regulatory Model Name

The regulatory model name of OAW-AP228 is APIN0228.

FCC

This device is electronically labeled. To view the FCC ID:
1. Log into the controller WebUI
2. Navigate to 

Maintenance > Controller > About

.

FCC Class B Part 15

This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation 

is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause 

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, 

may cause interference harmful to radio communications.
If this equipment does cause interference, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or more of the following 

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

!

CAUTION

Alcatel-Lucent access points must be installed by a professional installer. The professional installer is 
responsible for ensuring that grounding is available and it meets applicable local and national electrical codes.

!

CAUTION

RF Radiation Exposure Statement:

 This equipment complies with FCC RF radiation exposure limits. This 

equipment should be installed and operated with a minimum distance of 9.84 inches (25 cm) between the 
radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating 
in conjunction with any other antenna or transmitter. 

!

CAUTION

RF Radiation Exposure Statement:

 When operated in the 5.15 to 5.25 GHz frequency range, this device is 

restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite 
Systems.

!

CAUTION

Changes or modifications to this unit not expressly approved by the party responsible for compliance could 
void the user’s authority to operate this equipment.

Summary of Contents for OAW-AP228

















Reviews: