background image

OAW-AP228 Wireless Access Point

| Installation Guide

13

Connect the equipment to an outlet on a circuit different from that to which the receiver is 

connected.

Consult the dealer or an experienced radio or TV technician for help.

EU Regulatory Conformance 

Alcatel-Lucent hereby declares that the APIN0228 device model is in compliance with the 

essential requirements and other relevant provisions of Directive 1999/5/EC -CE(!). The Declaration of 

Conformity made under Directive 1999/5/EC is available for viewing at 

www.alcatel-lucent.com/

enterprise

.

Proper Disposal of Alcatel-Lucent Equipment

For the most current information about Global Environmental Compliance and Alcatel-Lucent 

products, see our website at 

www.alcatel-lucent.com/enterprise

.

Waste of Electrical and Electronic Equipment

Alcatel-Lucent products at end of life are subject to separate collection and 

treatment in the EU Member States, Norway, and Switzerland and therefore are 

marked with the symbol shown at the left (crossed-out wheelie bin). The treatment 

applied at end of life of these products in these countries shall comply with the 

applicable national laws of countries implementing Directive 2002/95/EC on Waste 

of Electrical and Electronic Equipment (WEEE).

European Union RoHS

Alcatel-Lucent products also comply with the EU Restriction of Hazardous 

Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific 

hazardous materials in the manufacture of electrical and electronic equipment. 

Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed 

circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Alcatel-Lucent 

products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in 

printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at 

the left indicating conformance to this Directive.

China RoHS

Alcatel-Lucent products also comply with China environmental declaration 

requirements and are labeled with the “EFUP 10” label shown at the left.

10

Summary of Contents for OAW-AP228

















Reviews: