Albatron KM266 Series Manual Download Page 50

Page: 50 / 63

USB Wake Up

This item allows you to select USB devices to awaken the

system from suspend mode.

The Choices: Disabled (default), Enabled.

VGA

When set to On, any event occurring at a VGA Port will awaken

a system which has been powered down.

The Choices: OFF (default), On.

LPT & COM

When this option is set to On, any event occurring at a

COM(serial)/LPT (printer) port will awaken a system which has
been powered down.

The Choices: LPT/COM (default), COM, LPT, NONE.

HDD & FDD

When set to On, any event occurring on a hard drive or a floppy

drive will awaken a system which has been powered down.

The Choices: ON (default), OFF.

PCI Master

When set to On, you need a LAN add-on card which supports

the power function. It should also support the wake-up on LAN

jumper.

The Choices: OFF (default), ON.

LAN Wake Up

To use this function, you need a LAN add-on card which support
power on function. It should also support the wake-up on LAN

jumper.

The Choices: Disabled (default), Enabled.

PCI PME Wake Up

When you select Enabled, a PME signal from PCI card returns

the system to Full ON state.

The Choices: Disabled (default), Enabled.

Summary of Contents for KM266 Series
































































Search results

Summary of Contents for KM266 Series

Reviews:

Related manuals for KM266 Series

Brands by name

Popular brands

Albatron KM266 Series, Manual

Search results

Summary of Contents for KM266 Series

Reviews:

Related manuals for KM266 Series

Brands by name

Popular brands