manualshive.com logo in svg

Albasca MK-5800, Configuration Manual, Page: 2 / 128

Share
Download
Albasca MK-5800 Configuration Manual Download Page 2

 

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 

part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful 
interference  in  a  residential  installation.  This  equipment  generates,  uses  and  can  radiate  radio  frequency 

energy and, if not  installed and used in accordance with the instructions, may cause  harmful interference  to 

radio  communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a  particular 
installation. If this equipment  does cause  harmful interference to radio or television reception, which can be 

determined by    turning the equipment off and on, the user is encouraged to try to correct the interference by 
one or more of the following measures: 

-Reorient or relocate the receiving antenna.  

-Increase the separation between the equipment and receiver. 

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

-Consult the dealer or an experienced radio/ TV technician for help. 

CAUTION: 

Any changes or modifications not expressly approved by the grantee of this device could void the user's 

authority to operate the equipment. 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1)

 

this device may not cause harmful interference, and 

(2)

 

this device must accept any interference received, including interference that may cause undesired 

operation. 

RF exposure warning 

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) 

used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons 

and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and 
installers must be provide with antenna installation instructions and transmitter operating conditions for 
satisfying RF exposure compliance. 

 

End Product Labeling

 

This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm 

may be maintained between the antenna and users. The final end product must be labeled in a visible area with 

the following:   "

Contains FCC ID: YKH319-BT82600 

“

 

  Information for the OEMs and  Integrators 

The following statement must be included with all versions of this document supplied to an 

OEM or integrator, but should not be distributed to the end user. 

1) This device is intended for OEM integrators only. 

   

2) Please  see the full Grant of Equipment document for other restrictions. 

 

Summary of Contents for MK-5800

































































































































Reviews:

No comments