background image

Thermostat Z-Wave Specification

 

June 26, 2019 

 

Building 36 Technologies 

An Alarm.com Company 

 

 

 

5

 

Configuration Command Class 

Temperature parameters take the form of 4-byte Z-Wave temperature commands where byte 1 
is the (precision|scale|size) and bytes 2 and 3 are the 16-bit signed temperature value.  Byte 4 
is unused.  The thermostat will format temperature reports with the same scale as the 
thermostat display temperature units.   If the temperature value is 0xFFFF (e.g. 0x2AFFFF00) 
the parameter is disabled. 

5.1

 

Parameters 

5.1.1

 

0x01 : HVAC Type (normal | heat pump) 

 

0x00 - Normal (DEFAULT) 

 

0x01 - Heat Pump 

 

Size 1 byte 

5.1.2

 

0x02 : Number of Heat Stages / Auxiliary Heat Stages (0 | 1 | 2 | 3) 

 

Default 2 

 

Size 1 byte 

5.1.3

 

0x03 : Number of Cool Stages / Heat Pump Stages (0 | 1 | 2) 

 

Default 2 

 

Size 1 byte 

5.1.4

 

0x04 : Heat Fuel Type (Fossil | Electric) 

 

0x00 - Fossil 

 

0x01 

 Electric (DEFAULT) 

 

Size 1 byte 

5.1.5

 

0x05 : Calibration Temperature (-10°F to 10°F), 1°F increments 

 

Default 0°F 

 

Size 4 bytes 

5.1.6

 

0x06 : Swing (0.0°F to 3°F), 0.5°F increments 

 

Default 0.5°F  

 

Size 4 bytes 

5.1.7

 

0x07 : Overshoot (0.0°F to 3°F), 0.5°F increments 

 

Default is 0.0°F 

 

Size 4 bytes 

 

 

Summary of Contents for Building 36 ADC-T3000





















Reviews: