manualshive.com logo in svg

Alarko HARMONY - D, Installation And Servicing Instructions, Page: 9 / 72

Share
Download
Alarko HARMONY - D Installation And Servicing Instructions Download Page 9

9

 

DECLERATION OF CONFORMITY AND CERTIFICATION 

Alarko Carrier manufacture boilers referred to in this booklet are pro-

duced in conformity with below: EC Directives and can hold the CE mark. 
2009/142/EC Gas Appliances Directive 

92/42/EEC Efficiency Directive

2004/108/EC Electromagnetic Compatibility Directive
2006/95/EC Low Voltage Directive

The appliances are certified to comply with the requirements of EN 297, 

EN 483 and EN 625 using the gas categories listed below:

2H

 and 

2E

; G20 gas with a governed gas supply at 20 mbar inlet pres-

sure

3 B/P

; any mixture of G30 and G31 gases with a governed gas supply 

at 29-mbar-inlet pressure 

3

+; G30 / G31gases with non-governed gas 

supplies at 29 / 37 mbar inlet pressures, respectively.

TERMS AND CONDITIONS OF GUARANTEE AND SERVICE 

Your boiler is guaranteed for material defects and mechanical failure as 

written on the Guarantee Form.
The guarantee is only valid if the appliance is installed in accordance 

with this manual.

Guarantee is not valid under below conditions.

•   Installation by unauthorized persons.
•   Hazards due to service by unauthorized persons.
•   Hazards due to natural disaster.
•   Hazards due to bad weather conditions, especially frost, unless in

-

structions in this booklet are obeyed.

•  Damaged or changed serial number of boiler.
•  Incorrect installation, use and maintenance with respect to the in

-

structions and the regulations in force.

•  Boilers produced for display and exhibition purposes. 

Summary of Contents for HARMONY - D









































































Reviews:

No comments