Alarko HARMONY - D Installation And Servicing Instructions Download Page 55

Page: 55 / 72

5.1.2 Parameter selection mode

• By pressing RESET switch for 1 touch it is possible to select param

eters.

• By pressing RESET switch for more than 5 sec., the modification

menu is entered then the actual value is shown.

5.1.3 Parameter changing mode

• By moving DHW knob, the desired value can be chosen (SET word

appears on LCD screen).

• If RESET switch is pressed for a time greater than 5 sec., the modi

fication is memorized and the system returns to PARAMETER SE

LECTION MODE with the following parameter already selected.

By moving the CH knob, it is possible to exit PARAMETER MODE.
After 2 minutes without performing anything through DHW knob, an au-

tomatic exit is forced and boiler will go back to its normal operating con-

dition.

HARMONY_D USERS INSTALLATION AND SERVICE MANUAL



By rotating DHW knob P1 value can be set.



To save the selected P1 value, leave DHW knob in the selected position and press

RESET switch for 5 sec.

* Since the display has two digits, P letter and corresponding numbers are visualized

alternatively.

5.1.2 Parameter selection mode



By pressing RESET switch for 1 touch it is possible to select parameters.



By pressing RESET switch for more than 5 sec., the modification menu is entered then

the actual value is shown.

5.1.3 Parameter changing mode



By moving DHW knob, the desired value can be chosen (SET word appears on LCD

screen).



If RESET switch is pressed for a time greater than 5 sec., the modification is memorized

and the system returns to PARAMETER SELECTION MODE with the following

parameter already selected.

By moving the CH knob, it is possible to exit PARAMETER MODE.

After 2 minutes without performing anything through DHW knob, an automatic exit is forced

and boiler will go back to its normal operating condition.

Table 6 Parameter Adjustment

Locally

on board

Description

Value

Ignition capacity

Adjustable 0 - 63%

Gas type

MTN

LPG

3rd

4th

CH off time

Adjustable 0 - 255 sec.

CH max capacity

Adjustable 0 - 100%

Range CH

Normal

Reduced

DHW switch off temp

65°C

Set point

LED strip configuration

(#12 leds)

Always ON * ON when flame

is ON *

Always

OFF

** = Since the display has two digits, if parameter is greater than 99, the first digit is displayed in turn with the other two digits:

e.g. if parameter = 136: 01 is displayed in turn with 36

* When LCD backlight is ON, LED strip is switched OFF independently from LED strip configuration value.

5.1.4

PARAMETERS’ ADJUSTMENT

Authorized service can change seven of the parameters related to boiler operation via using

the reset button and knobs on the control board.

Ignition Gas Pressure:

It controls the outlet gas pressure of gas valve during ignition

period. By using Table 6, adjustment can be done as percentage. Default setting of P01

Summary of Contents for HARMONY - D









































































Search results

Summary of Contents for HARMONY - D

Reviews:

Alarko HARMONY - D, Installation And Servicing Instructions, Page: 55 / 72

Search results

Summary of Contents for HARMONY - D

Reviews: