manualshive.com logo in svg

Alamo INTERSTATER, Operator'S Manual

Share
Download
Alamo INTERSTATER Operator'S Manual Download Page 172

MAINTENANCE

INTERSTATER   03/09

Maintenance Section 5-18

© 2009 Alamo Group Inc.

MAINTENANCE

POSSIBLE TROUBLE

CAUSES

REMEDIES

System will not operate in

Oil supply low.

Check oil level and fill.

either direction.

Oil Filter clogged.

Replace Filter Element.

Oil too heavy.

Use proper viscosity oil.

Drive Coupling broken.

Inspect Coupling for sheared Spline
Spline or Key.

System noisy.

Air in system due to low oil level.

Fill in reservoir to sight glass.

Loose Suction Line.

Tighten Fittings.

Clogged Suction Filter.

Replace Filter Element.

Internal Pump or Motor damage.

Disassemble, inspect, and repair.

Sluggish response to 

Air in system.

See Step 1A, 1B, 1C, 2B

acceleration

Internal Pump or Motor wear

Disassemble, inspect, and repair.

or damage.

Summary of Contents for INTERSTATER



























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands