manualshive.com logo in svg

Alamo BUSH HOG RMB 1660, Operator'S Manual

Share
Download
Alamo BUSH HOG RMB 1660 Operator'S Manual Download Page 152

OPERATION

RMB 1660   01/22

Operation Section 4-30

© 2022 Alamo Group Inc.

OPERA

T

ION

13.3 Driving the Tractor and Boom

Start off driving at a slow speed and gradually increase your speed while maintaining complete control of the
tractor.  Never operate the tractor at speeds that cannot be safely handled or which will prevent the operator
from stopping quickly during an emergency.  If the power steering or engine ceases operating, stop the tractor
immediately as the tractor will be difficult to control.

Perform turns with the tractor and mower at slow
speeds to determine how the tractor with and
attached implement handles a turn. Determine the
safe speed to maintain proper control of the tractor
when making turns. When turning with the
implement the overall working length and width of
the unit is increased. Allow additional clearance for
the unit when turning or when passing large
obstructions. 

To avoid overturns, drive the tractor with care and
at safe speeds, especially when operating over
rough ground, crossing ditches or slopes, and
turning corners. Use extreme caution when
operating on steep slopes. Keep the tractor in a low
gear when going downhill.  DO NOT coast or free-
wheel downhill.

OPS-B- 0006

Never leave the mower unattended while the head is in the raised

position. The mower could fall causing serious injury to anyone who

might inadvertently be under the mower

 

 (SBM-4)

Always keep a careful lookout and use extreme care when working
around overhead obstructions. Never allow the mower head or boom
within 10 feet of any power line. When working close to overhead
power lines consult your electric company for a safe code of operation.

(SBM-7)

Summary of Contents for BUSH HOG RMB 1660







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands