manualshive.com logo in svg

Alamo BUSH HOG RMB 1660, Operator'S Manual

Share
Download
Alamo BUSH HOG RMB 1660 Operator'S Manual Download Page 149

OPERATION

RMB 1660   01/22

Operation Section 4-27

© 2022 Alamo Group Inc.

OPERA

T

ION

11.1 Working on Adverse Slopes

When working high with the reach fully extended, it
is possible for the main arm balance to go ‘Over-
Center’ and take the weight off the lift cylinder. A
restrictor in the gland connection of the lift ram
prevents sudden unpredictable movements should
this occur. 

NOTE:

 Always inspect the work area prior to cutting

to remove hazardous material and note any
immovable objects.

12. Lift Float Kit (Optional)

Fitting Location

The hydraulic float kit should be mounted to the
special bracket in such a position that it does not
foul any other component during the slewing
motion.    

Summary of Contents for BUSH HOG RMB 1660







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands