AL-KO G4022012, Translation Of The Original Instructions For Use

Page: 29 / 344

469905_b 29
Commissioning/Decommissioning
2. Check that all parts have been delivered (see
chapter 2.3 "Scope of supply", page 24 ).
3. Check all parts for transport damage.
If any damage is evident or parts are missing,
immediately inform the dealer where the ap-
pliance was purchased.
4.2 Mounting the lower brace (02)
1. Position both ends of the lower brace (02/1)
against the pipe ends (02/2) (02/a) in such a
way that the insertion holes of the lower
brace and the pipe ends line up.
2. Insert two long locking screws (02/3) from the
inside.
3. Place a washer (02/4) on each of the locking
screws.
4. Screw star handles (02/5) onto the locking
screws and firmly tighten.
4.3 Mounting the intermediate brace (03)
1. Push both ends of the intermediate brace
(03/1) onto the lower brace (03/2) (03/a) in
such a way that the insertion holes of the in-
termediate brace and lower brace line up.
The guide (03/3) for the adjusting crank must
point upwards.
2. Insert two long locking screws (03/4) from the
inside.
3. Place a washer (03/5) on each of the locking
screws.
4. Screw star handles (03/6) onto the locking
screws and firmly tighten.
4.4 Mounting the upper brace (04)
1. Push both ends of the upper brace (04/1) on-
to the intermediate brace (04/2) (04/a) in
such a way that the insertion holes of the up-
per brace and intermediate brace line up.
The motor switch, motor switch bracket, han-
dle and LED light must point upwards.
2. Insert two long locking screws (04/3) from the
inside.
3. Place a washer (04/4) on each of the locking
screws.
4. Screw star handles (04/5) onto the locking
screws and firmly tighten.
4.5 Fixing the cables to the bar (05)
1. Fix the cable (05/1) of the motor switch with a
cable holder (05/2) to the intermediate brace
and to the lower brace.
2. Fix the cable (05/3) of the LED light with a
cable holder (05/2) to the intermediate brace
and to the lower brace.
4.6 Installing the adjustment crank (06, 07)
Connecting the adjustment crank to the
extension shaft (06)
1. Insert the adjusting crank (06/1) through the
guide (06/2) onto the intermediate brace (06/
a) from above.
2. Insert the adjustment crank into the support
(06/3) of the extension shaft up to the end
stop (06/b).
3. Align the adjusting crank and the extension
shaft so that their holes line up.
4. Push a cotter pin (06/4) through both bores
(06/c) until it clicks into place.
Installing and fixing the adjustment crank
onto the appliance (07)
1. Insert the extension shaft (07/1) into the
mounting (07/2) on the appliance (07/a).
2. Rotate the extension shaft so that its hole
and the hole of the mounting line up.
3. Push a cotter pin (07/3) through both bores
(07/b) until it clicks into place.
4. Turn the star handle (07/4) onto the guide
(07/5) and slightly tighten it to fix the adjust-
ment crank (07/c) in place.
4.7 Installing the snow deflector (08)
1. Place the snow deflector (08/1) on the dis-
charge channel (08/2) so that the lugs (08/3)
engage in the recesses of the snow deflector
on the left and right.
2. Insert two short locking screws (08/4) through
the holes of the discharge channel from the
inside.
3. Place a washer (08/5) on each of the locking
screws.
4. Screw star handles (08/6) onto the locking
screws and firmly tighten.
5 COMMISSIONING/
DECOMMISSIONING
5.1 Charging the rechargeable battery (09,
10)
The rechargeable battery and the charging unit
are not included. The following li-ion recharge-