background image

 AK-CI-01 - user manual 

p. 3

ź

Do not connect devices which require voltage greater that 5 V DC and current greater that 2.1 A 
and 1 A (depending on the socket) to USB sockets.

ź

It is forbidden to connect devices equipped with transformer or induction motors, i.e. power 
tools,  household  appliances,  transformer  power  supplies  or  pumps.  It  may  damage  the 
inverter.

ź

Do not power the inverter with a flat or broken battery.

ź

Do not connect the inverter to an AC power source.

ź

Product can work both the car engine turned on and off.

ź

To prevent car battery from discharging, it is recommended to start the engine for about 15 
minutes for every 2 hours of operation of the inverter.

ź

Turn off the inverter before turning on the car engine. 

ź

If the fuse is blown, replace it with a new one.

ź

Avoid placing the inverter near to radio and antenna, beacause it can cause interference of the 
signal.

ź

The product can not work without surveillance.

ź

The inverter can not be used after changing a cold to a warm room. Wait until the inverter 
reaches the room temperature.

ź

It is forbidden to insert objects inside the inverter case.

ź

Connection of inverter to electricity is made by plugging the cable with the cigarette lighter plug 
to corresponding socket in your vehicle.

ź

Inverters plug should be disconnected from the power socket if the product is not in use for a 
long time.

ź

When disconnecting the power cord from the socket and from the device, do not pull on the 
cord, but only on the part of the cable plug provided for this purpose.

ź

In case of any doubts regarding operation, safety or connection of the product, please contact 
the manufacturer or a qualified specialist for this purpose.

ź

All maintenance, adjustment and repair work on the product may only be carried out by a 
qualified person in a specialist facility.

car power inverter

1.

Turn off the inverter.

2.

Insert power plug of the inverter in cigarette lighter socket.

3.

Turn on the inverter. When the green LED (normal) is shining the inverter works propely.

4.

Connect selected device to the inverter. When the red LED (warning) is shining the inverter 

can be overloaded or car battery is flat.

Preparing the Car Power Inverter:

Fuse changing

1. Prepare a new glass 20 A fuse.
2. Unscrew the end of the plug.
3. Remove broken fuse.
4. Insert a new fuse.
5. Tighten the end of the plug.

Cleaning the Car Power Inverter:

ź

Use soft and  antistatic cloth for cleaning the power inverter.

ź

Do not use abrasive or chemical cleaners.

Disconect the power inverter from the electrical socket and connected devices before cleaning.

Summary of Contents for AK-CI-01






Reviews: