background image

9

Operation

Messages

MESSAGES

Pump down malfunction error (stop), the time configured in parameter C20 has been exceeded 
(see p. 11). 
Only displayed on screen.

Pump down malfunction error  (start-up), the time configured in parameter C19 has been 
exceeded (see p. 11). 
Only displayed on screen.

Probe 1/2/3 failure (open circuit, crossed circuit or temperature outside the limits of the probe) 
(Equivalent limits in °F). 
Only E2 and E3: Damp evaporator probe (see p. 18).
Activates the alarm relay and the audible alarm.

Open door alarm. Only if the door remains open for a longer time than defined in parameter 

A12

 (see p. 19). 

Activates the alarm relay and the audible alarm.

Maximum temperature in control probe alarm. The temperature value programmed in 

A1

 has 

been reached (see p. 18).
Activates the alarm relay and the audible alarm.

Minimum temperature in control probe alarm. The temperature value programmed in 

A2

 has 

been reached (see p. 18).
Activates the alarm relay and the audible alarm.

External alarm activated (by digital input) (see p. 18).
Activates the alarm relay and the audible alarm.

Severe external alarm activated (by digital input) (see p. 18).
Activates the alarm relay and the audible alarm.

Alarm for defrost completed due to time-out. The time set in 

d1

 has been exceeded (see p. 20).

Activates the alarm relay and the audible alarm.

HACCP alarm. The temperature has reached the value of parameter 

h1

 during a longer period 

than established in 

h2

 (see p. 19).

Activates the alarm relay and the audible alarm.

HACCP alarm due to a power supply failure. The temperature established in 

h1

 has been 

reached, following a power supply failure (see p. 19).
Activates the alarm relay and the audible alarm.

Indicates that a defrost is being performed (see p. 15).
Only displayed on screen.

Password request. See parameters 

b01

 and 

PAS

 (see p. 20).

Only displayed on screen.

Shown sequentially with the temperature:

 The controller is in demo mode, the 

configuration has not been made.

1652H302 Ed.03

Summary of Contents for AKO-16520

































Reviews: