4
CHANNELS SECTION
MASTER SECTION
MONITORING SECTION (CUE)
VCA SECTION
CROSSFADER SECTION
SEND/RETURN SECTION:
Input Selectors
line or cd
phono
mic
Input sensibility control GAIN:
Channel Equalizer:
Balance
:
Level meter:
Mono/Stereo Selector:
Booth
level control:
Headphones level control:
Caution!
Return Level control
Return signal Monitoring
By means of the 2 position levers at each
channel choose the source to be assigned to the channel.
According to the type of signal we can choose between:
: This is a line lever signal. We can found it in CD
Players, MD Players, Cassette Players and other domestic
devices.
: We find this type of signal in Turntable cartridges.
Previous to be processed in the mixer is equalized by a RIAA filter
included in the mixer.
: For microphone only.
And at Ch-2 we can select USB by means of control
and control
.
GAIN sets input sensibility of each channel. By means of this
control we adjust input level to mixer optimum level. To set input
level turn GAIN pot until let BAR
of respective channel
depicts around 0dB. Over this value we are close to saturation. This
task will have to be done for each of the channels because
differents inputs sources may have differents levels.
3 band equalizer is provided for each
channel. These 3 bands are set at High 13KHz, Mid 1KHz, Low
70Hz. Notice that when increasing any tone level we increase the
overall level of the signal and we can reach saturation. Is advisable
to watch carefully the output lever meters to avoid this situation.
Led bar displays signal
level relative to an optimal working level
.
Will allow us to monitor input level. Level on Led bar is
independent from channel fader but will depend on GAIN and
Equalizer settings.
Red Leds light indicates saturation. Yellow Leds light indicates
near saturation. Green Led light indicates safe zone. Proper
setting is when red leds lights only in musical peaks for a short
lapse of time.
Set channel volume to master mix
¨0¨ position no signal is routed to Master bus. In “10” position,
100% of channel signal is routed to Master bus.
To be in-field replaceable,
this part is front-detachable. For replacement, switch off the unit
and unscrew the
outer screws of the plate and remove the part;
detach the connector and replace the part. Plug in the connector
and screw the new part to the main body again.
The signal's stereo balance can be
controlled by means of control Balance Master
. This signal
is displayed on the level meter.
The level meter shows the stereo
output level of Master output. Two ten segment LED bars are
available with -20/+9 dB range.
We can transform output signal,
normally stereo, in mono.
Controls
. Please note that the level of
this output will not in any case be displayed on the level meter;
consequently, please check carefully for your amplifier not being
overloaded.
With a stereo headphone
connected, you may control the headphones volume. Please check
your headphones impedance for a minimum of 32 Ohms and be
aware of high-impedance headphones reducing the maximum
output power of this output, so that you should choose a
headphone with less than 200 Ohms of impedance.
Set level carefully, output signal is powerful enough to
damage your ears. We recommend start setting from control
turned fully counter clockwise.
right
I- Control turn to PGM we heard the master mix pre Master
fader. Master mix will depend upon Channels faders setting.
II- Control turn to
we heard the Channels with CUE toggle
activated.
When the control is in between the to extreme positions we heard a
blend of both PGM and CUE signals.
Adjust the mix volume of the sources selected to
left (A) and right (B) side. We can adjust crossfader curve shape by
means of control
.
When
is active a
LED lights up.
Switches ON/OFF the crossfader. For
those not using the crossfader, selecting OFF will make things
easier as signal by passes it. When Crossfader is active a Red LED
lights up.
Sets the level of returned signal
throught the Return connector. Monitoring of incomming signal is
done with the ten LED segment bar
ten LED segment bar depict
the level of Retun signal. To set properly the Return signal level act
upon control
.
Red Leds light indicates saturation. Yellow Leds light indicates
near saturation. Green Led light indicates safe zone. Proper
setting is when acting upon control
red leds lights only in
musical peaks for a short lapse of time.
When
is active a
LED lights up.
(1)
(44)
(1)
(1)
(6)
(19)
( )
(24)
(25)
Please be aware of
the final output level to be adjusted by the Master and Booth
controls. Furthermore, the level of the channels can depend on the
setting of the Crossfader if these channels are assigned to it by
means of the Crossfader assign control.
:
Secondary Input selectors:
Channel 1 Submic selector:
Channel level meter:
Channel CUE assign toggles (CUE):
Attention:
Channel Fader:
Attention
Crossfader assign:
Master level control:
control
Master
Cue Panoramic control:
Headphones connector :
Channel Faders curve selector:
Crossfader curve selector:
Crossfader:
Reverse Control :
Crossfader ON/OFF:
Source Selector:
:
:
Return CUE:
Return ON/OFF :
This control depends upon
control
selection. Using the 2 position slide switch on each
channel we can choose between a Line and a Phono level input
signal.
At Channel 1 when Selector
is set to the left we can choose between 2 input signals, Line
and Submic that is the secondary Microphone input.
10 segment
(named nominal level)
Level setting:
Switching the toggles
we activate CUE on each respective channel. Meaning that the
signal of the channel will be available for headphones monitoring.
before starting monitoring keep the headphones level
at minimum. The mixer is fitted with a powerful output amplifier
that can damage your hearing.
s
. While at
6
: Before performing this operation switch off your
mixer and unplugg it.
For each channel we can send its signal to:
-A: Left side of Crossfader (Yellow LED)
-B: Right side of Crossfader (Orange LED)
Sets the overall output level.
sending to left or
right
modification
a secondary amplifier,
normally placed at the control room
By means of this function, you can
preview your forthcoming mix by crossfading between the
preselected headphones signal on the left side of the control and
the Master output signal (pre pot) on the
side of the control.
:
CUE:
Plug your headphones at the Jack
6.3 TRS.
Sliding this 3 position
control you can choose between three different curves for the
Fader action. From
to
the slope of the curve
increases.
Sliding this 3 position control
you can choose between three different fading curves between A
and B sources. From
to
the slope of the curve
increases.
Pressing this control you will switch
Crossfader left to Right and viceversa.
Reverse
Yellow
This rotary switch allows to choose any
Channel or Master to Send signal.
25 .
This
RETURN Level setting:
Sends the return signal to headphones for
monitoring. As well as the Main Mic signal. Red LED will light
when function activated.
This control enables the return signal to
Master bus. So to speak is like an Return ON/OFF or Effects
ON/OFF.
Return ON/OFF
Green
+ info pag 7
SOFT
SHARP
+ info pag 7
SOFT
SHARP
+ info pag 7
+ info pag 6/8
CONTROLS AND F
U
NCTIONS
E
NGLISH
2
7
10
1
3
4
5
6
8
9
11
12
13
15
16
14
17
19
18
20
21
22
23
25
26
27
24
