AJA Io Express Installation And Operation Manual Download Page 31 | Manualshive

Page: 31 / 132

background image

1

21

Io Express Installation and Operation Manual — Cabling the System

Click Next to begin the installation.

Installation Progress Screen.

When the installer has completed copying the AJA Windows Software to disk, you will see a
standard Windows Logo test warning. Click on the “Continue Anyway” button to finish the
installation.

When the installation is completed, a final screen will be displayed announcing that “Setup has
finished installing AJA Windows Software on your computer.” Click on the Finish button after the
installation is complete. Restart the computer after installation to activate the Io Express.

«
...
29
30
31
32
33
...
»

Summary of Contents for Io Express





































































































































Reviews:

No comments

Related manuals for Io Express

Brand: PAT Pages: 55

Brand: PAT Pages: 31

Brand: Vcheck Pages: 31

Brand: Eagletone Pages: 2

IEM-100 Beltpack

Brand: DAPAudio Pages: 19

MIC TRAC MT-3000

Brand: GAGEMAKER Pages: 20

Brand: Oceanic Pages: 152

Brand: Kaiterra Pages: 8

Brand: Kaiterra Pages: 12

Brand: Raytech Pages: 18

Brand: Tavool Pages: 12

Brand: UEi Pages: 8

Brand: bmcm Pages: 5

Brand: Tektronix Pages: 48

Brand: Kawai Pages: 72

Brand: PCE Health and Fitness Pages: 66

Brand: THORLABS Pages: 20

Brand: Haltech Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands