Preset timing 1 LED
30 min
Power-on time 1 LED
15 min
Temperature about 60-120 ° C
1 LED
about 60 °C
2 LEDs
about 64°C
4.3 EXAMPLES
The desired temperature in the sauna is about 100 °C and the heater is desired to be switched
on for 2.5 hours at a time.
1. Switch on the power using the I/O button.
2. Depress the SET button -> the yellow LED flashes.
3. Depress the SET button a second time -> the green LEDs flash.
4. Depress the + or - button as many times as is necessary to illuminate10 LEDs.
5. Depress the SET button -> the red LEDs flash.
6. Depress the + or - button as many times as is necessary to illuminate 11 LEDs.
7. Depress the SET button -> the heater is switched on and the set values will be saved for
the next time.
You wish to switch on the heater in about 3 hours
1. Switch on the power using the I/O button.
2. Depress the SET button -> the yellow LED flashes.
3. Depress the + or - button as many times as is necessary to illuminate 6 LEDs.
4. Depress the SET button -> the green LEDs flash.
5. If you want to keep the set power-on time, depress the SET button; to change the power-on time,
use the + or - buttons
6. The red LEDs will flash after the SET button has been depressed. If you wish to set the
temperature, you can use the + or - buttons; if not, just depress the SET button to turn the pre-set
timing on.
4.2 SETTINGS
-
When the heater is switched on, the power-on time, which will be saved in memory, can be set within
about 1 minute. After this, the heater goes into its normal operating mode, and any subsequent
settings of the power-on time will only affect the current heating session.
- The first preset time LED starts to flash as soon as you depress the SET button.
-
After this, the desired preset time can be selected using the + /- buttons. Please note that after the
SET button has been depressed, the first flashing LED indicates only the state of the preset timing.
If you wish to set the preset time to 30 min, you need only to depress the + button once so as to
save the set value in the memory.
-
Depress the SET button a second time to save the preset time setting in memory.
After that, the green LEDs will flash to indicate that you are now able to set the power-on time via the
+/- buttons.
After having set the desired power-on time is set, press the SET button again.
Now, the desired power-on time will be saved in memory.
-
After the SET button is depressed, the red LEDs will flash.
You can then set the desired temperature via the +/- buttons.
After this, depress the SET button one more time to make the heater go into the set mode, where the
LEDs are continually illuminated to indicate the current status.
- If the yellow LEDs are lit, the preset timing is active.
- If the green LEDs are lit, the heater is switched on.
- The red LEDs are always lit when the heater is in operation, indicating the set temperature.
-
Once the heater has been set, the set values will remain in memory, and when power is switched on
via the I/O button, the heater will always be warmed up in the same way for the same set period of
time. The preset time, however, will always be zero. If you wish to apply the preset timing feature,
you will always need to activate it separately.
-
If the SET button is not pressed after the setting, the LEDs will continue flashing for about
1 minute. After this, the heater will automatically return to its normal operating mode.
Summary of Contents for 90212
Page 31: ...Kytkin 10 9...
Page 37: ...10 9...
Page 79: ...10 9...
Page 92: ...08 2011 Narvi Oy Yritt j ntie 14 27230 Lappi Finland Tel 358 207 416 740 www narvi fi...
