Aisin AWGP180E1NHS Installation Instructions Manual Download Page 49

Page: 49 / 76

Main Unit and Piping

Electrical

Test Operation

Reference

10. Power Supply Wiring Procedure

[Stand-alone installation]

Important reminder

Do not connect the indoor/outdoor unit signal wires of a different system.

Doing so could result in improper operation.

In order to avoid

attaching 3 wires to

the terminal, connect

the wire from the

terminal unit of the

outdoor and outdoor

unit wiring.

If there is a branching,

use a relay terminal.

To the other system

All of indoor/outdoor and

outdoor/outdoor unit signal

wires must be non-polarity

2 core cable.

Point

Be sure to wire for ever y

refrigerant piping system.

Indoor/outdoor unit signal wire

Point

Signal wire between refri-

gerant piping systems.

Maximum number of the

connectable refrigerant

piping systems is 10.

Outdoor/outdoor unit signal wire

Point

Important reminder

Maximum number of the connectable indoor units on a network is 128.
Signal wires between the indoor units of the same refrigerant system must

be connected to the In-Out terminal of the outdoor unit in the same system.
The signal wires cannot be connected to the Out-Out terminal, or an
outdoor unit in the different system.

Single-phase

230 VAC

or 208 VAC

Power supply

Single-phase

230 VAC

or 208 VAC

Power supply

Single-phase

230 VAC

or 208 VAC

Power supply

Remote controller

Indoor unit

Remote controller

Outdoor unit C
(Master unit)

Outdoor unit A
(Master unit)

Single-phase

230 VAC

or 208 VAC

Power supply

I : In
O : Out
RC: Remote controller

Centralized

control unit

Indoor unit

System

①

②

Summary of Contents for AWGP180E1NHS













































































Search results

Summary of Contents for AWGP180E1NHS

Reviews:

Related manuals for AWGP180E1NHS

Brands by name

Popular brands

Aisin AWGP180E1NHS, Installation Instructions Manual

Search results

Summary of Contents for AWGP180E1NHS

Reviews:

Related manuals for AWGP180E1NHS

Brands by name

Popular brands