Aisin AWGP180E1NHS Installation Instructions Manual Download Page 37

Page: 37 / 76

Main Unit and Piping

Electrical

Test Operation

Reference

5. Fuel Gas Piping Installation

Fuel Gas Piping Installation

�

The gas piping for the outdoor unit must be installed as shown below.

�

The device shown as

in the drawing below must be installed. This device is for servicing the fuel system.

�

Install the devices shown as

�

Use the valve indicating the “on” and “off” positions.

and

as necessary. These devices are for checking the supplied gas pressure

and filtering the gas.

Warning

�

Use only the fuel gas indicated on the name plate.

Using wrong type of fuel gas could cause incomplete combustion or could damage the out-
door unit.

�

Always perform a gas leakage test after connecting the piping.

If there should be a gas leakage, a fire or an explosion could occur.

�

Use soapy water or a gas leakage detector for performing the gas leakage test.

Using a flame reaction test could cause a fire or an explosion.

�

Always use a reinforced gas hose between the gas valve on the fuel gas piping and

outdoor unit.

Failure to do so could cause a gas leakage.

�

Install the piping so that the fuel gas pressure at the inlet port of the outdoor unit is

equal to the pressure required by the gas supply standard defined by the gas suppli-

ers.

Incorrect pressure of fuel gas could cause incomplete combustion or malfunction of the unit.

Important reminder

�

Do not apply pressure of over 0.6 psig (4.2 kPa) when testing the fuel gas line for leakage.

Doing so could damage the regulator inside the unit.

Gas fuel piping

connection (R3/4)

Rear side of outdoor unit

2 Pressure check tap

3 Strainer

1 Gas valve

OFF

Reinforced gas hose

Summary of Contents for AWGP180E1NHS













































































Search results

Summary of Contents for AWGP180E1NHS

Reviews:

Related manuals for AWGP180E1NHS

Brands by name

Popular brands

Aisin AWGP180E1NHS, Installation Instructions Manual

Search results

Summary of Contents for AWGP180E1NHS

Reviews:

Related manuals for AWGP180E1NHS

Brands by name

Popular brands