background image

Installation Procedure

15

Detach the service port's cap of gas stop valve, the valve rod's cap for liquid

stop valve and gas stop valve, and connect the service port into the projection

of charge hose (low) for gaugemanifold. Then connect the projection of

charge hose (center) for gaugemanifold into vacuum pump.

Open the handle at low in gaugemanifold, and operate vacuum pump. If the

scale-moves of gause (low) reach vacuum condition in a moment, check

the step 1 again.

Vacuumize for over 15min. And check the level gauge which should read -

0.1MPa (-76 cm Hg) at low pressure side. After the completion of vacuumizing,

close the handle 'Lo' in the vacuum pump. Check the condition of the scale

and hold it for 1-2min. If the scale-moves back in spite of tightening, make

flaring work again, then return to the beginning of the step 3.

Open the valve rod for the liquid stop valve to an angle of anticlockwise 90

degree. After 6 seconds, close the liquid stop valve and make the inspection

of gas leakge.

No gas leakage? In case of gas leakage, tighten parts of pipe connection. If leakage stops, then proceed the step 6. If it

does not stop gas leakage, discharge whole refrigerants from the service port. After flaring work again and vacuumize,

fill up prescribed refrigerant from the gas cylinder.

Detach the charge hose from the service port, open liquid stop valve and

gas stop valve. Turn the valve rod anticlockwise until hitting lightly.

To prevent the gas leakage, turn the service ports cap, the valve rodis cap

for liquid stop valve and gas stop valve a little more than the point where

the torque increases suddenly.

If the refrigerant of the air conditioner leaks, it is necessary to make all the refrigerant out. Vacuumize first, then charge

the liquid refrigerant into air conditioner according to the amount marked on the nameplate.

Vacuuming

Piping vavuum method: to use vacuum pump

1.

2.

3.

4.

5.

6.

7.

CAUTION:

90

Service port

90 for 6 sec.

Open

Liquid stop valve

Gas stop valve

Gauge manifold(R410A)

Vacuum pump(R410A)

Close

Valve rod cap
Valve rod cap

Service port cap

Liquid stop valve

Gas stop valve

Liquid stop valve

Gas stop valve

Summary of Contents for AWAU-YUDA060-H13





















Reviews: