Airwell AW-XDO009-H11 Installation Manual Download Page 21

21

1.3 

DB 35°C - WB 24°C

DB 18°C
DB 27°C

DB 5°C

EN

MAINTENANCE

Technical specifications 

Please read data plate to obtain the technical data listed below.

Power supply voltage

Maximum absorbed power

Maximum absorbed current

Amount of refrigerant gas

Casing protection rating

Note:

The product is compliant with the ERP (Energy Related Products) European directive.
It includes Commission delegated Regulation (EU) No 2016/2281, also known as Ecodesign Lot 21
Performances referred to the maximum speed fan (Max.)
1) Cooling: inlet air temperature 27°C w.b./19°C d.b.; in/out water temperature 30°C/35°C
2) Heating: inlet air temperature 20°C; in/out water temperature 10°C/7°C (well source)
3) Water flow rate measured in cooling at maximum speed fan (Max.)

Internal ambient temp.

Water inlet temp.

Maximum operating temperature in cooling mode

45° C

Minimum operating temperature in cooling mode

7° C

Maximum operating temperatures in heating mode

40° C

Minimum operating temperatures in heating mode

7° C

Operating limits 

Technical specifications
Size

XDO 09

XDO  012

Cooling

Cooling capacity

1

kW

2.53

3.56

Total power input

1

kW

0.384

0.762

EER

1

-

6.58

4.67

Heating

Heating capacity

2

kW

2.27

3,26

Total power input

2

kW

0.710

1.089

COP

2

-

3.20

3.00

Compressor

Type of copressor

-

Inverter driven

Inverter driven

N° of compressor

-

1

1

Refrigerant gas

R-410A

R-410A

Refrigerant charge

kg

0.75

0.75

Air handling section fan

Type of fan

-

Centrifugal

Centrifugal

Number of fan

-

1

1

Min. air flow rate

m

3

/h

195

220

Med. air flow rate

m

3

/h

250

310

Max. air flow rate

m

3

/h

310

410

Boost air flow rate

m

3

/h

385

435

Water side exchanger

Type of exchanger

-

Coaxial

Coaxial

Water flow rate

3

l/s

0.139

0.206

Water fittings

Eurokonus M 3/4"

Eurokonus M 3/4"

Power supply

Standard power supply

V/ph/Hz

230/1/50

230/1/50

Noise Levels

Sound power level 

dB(A)

52

57

Summary of Contents for AW-XDO009-H11

























Reviews: