Airstream 2013 SPORT Owner'S Manual Download

Page: 71 / 115

F - 2

F - 3

PLUMBINg

vent blockage, which could result in excessive gas pressure causing fire

or explosion.

DangEr

: The LPG bottles are securely mounted on the front

“A” frame of your trailer. If these bottles must be removed for service or

replacement it is important that they be reinstalled correctly in order to

prevent any possibility of them falling off or becoming dislodged during

travel.

LPG BOTTLES

The following step-by-step procedure gives you the proper method of remov-

ing and installing these bottles:

1. Remove the bottle cover and turn the knob on your automatic regulator so

the arrow points to the tank opposite the one to be removed. Shut off the gas

valve on the bottle to be removed.

2. Disconnect the rubber gas line at the bottle to be removed. (The green plastic

fitting is a right hand thread and no tools should be used.)

3. Turn the large clamping T-handle counterclockwise until the hold down

bracket is loose enough to remove the bottle. DO NOT REMOVE OR

LOOSEN THE CENTER HOLD DOWN ROD. It is fastened to the A-frame by

two hex head nuts. Periodically check the rod for tightness.

To Install

1. Place the bottle in position on the “A” frame and bottle cross member so that

it rests on the upper collar of both bottles with the collar rims engaged in the

grooves on the underside of the bracket. If your trailer is equipped with a gas

bottle cover it should be positioned over the bottles next. Make sure the hold

down rod projects up through the hole in the shroud center bracket.

2. Replace the T-handle and tighten down until the bottles are held firmly in

place.

3. Turn on gas shut off valves and test all fittings with a soap suds or detergent

solution and watch for bubbles.

If you have allowed both tanks to run out, air may have gotten into the lines. In

this event, the air must be forced out through the lines by gas pressure before

you will be able to light the pilots. Hold a match to the pilot of the appliance

closest to the tanks until it lights and stays lit. Then move to the next closest,

etc.

Warning

: Your LP tanks must be filled as directed by the tank

manufacturer. Instructions are located on a decal near the fill valve. The

decal must not be defaced.

Warning

: Your LP tanks must be, and can only be, placed

Summary of Contents for 2013 SPORT




















































































































Search results

Summary of Contents for 2013 SPORT

Reviews:

Related manuals for 2013 SPORT

Brands by name

Popular brands

Airstream 2013 SPORT, Owner'S Manual

Search results

Summary of Contents for 2013 SPORT

Reviews:

Related manuals for 2013 SPORT

Brands by name

Popular brands