AirStage ASUB18RLAV Installation Manual Download Page 8

Page: 8 / 17

En-7

For solid core wiring

(1) To connect the electrical terminal, follow the below diagram and connect after looping

it around the end of the cable.

(2) Use the speci

ed cables, connect them securely, and fasten them so that there is no

stress placed on the terminals.

(3) Use an appropriate screwdriver to tighten the terminal screws.

Do not use a screwdriver that is too small, otherwise, the screw heads may be
damaged and prevent the screws from being properly tightened.

(4) Do not tighten the terminal screws too much, otherwise, the screws may break.
(5) See the table for the terminal screw tightening torques.
(6) Please do not

x 2 power supply cables with 1 screw.

Loop

Screw with
special washer

Cable end (Loop)

Cable

Terminal block

Strip 31/32 in.

(25 mm)

WARNING

When using solid core cables, do not use the attached ring terminal. If you use the
solid core cables with the ring terminal, the ring terminal's pressure bonding may
malfunction and cause the cables to abnormally heat up.

B. For strand wiring

(1) Use ring terminals with insulating sleeves as shown in the

gure below to connect to

the terminal block.

(2) Securely clamp the ring terminals to the cables using an appropriate tool so that the

cables do not come loose.

(3) Use the speci

ed cables, connect them securely, and fasten them so that there is no

stress placed on the terminals.

(4) Use an appropriate screwdriver to tighten the terminal screws.

Do not use a screwdriver that is too small, otherwise, the screw heads may be
damaged and prevent the screws from being properly tightened.

(5) Do not tighten the terminal screws too much, otherwise, the screws may break.
(6) See the table for the terminal screw tightening torques.
(7) Please do not

x 2 power supply cables with 1 screw.

Sleeve

Screw with
special washer

Ring terminal

Cable

Terminal block

Ring terminal

Strip 13/32 in.

(10 mm)

WARNING

Use ring terminals and tighten the terminal screws to the speci

ed torques, otherwise,

abnormal overheating may be produced and possibly cause heavy damage inside
the unit.

Terminal number

Tightening torque

M4 screw

(Power supply/Change: L1, L2 (N), GND)

11 to 16 Ibf·in

(1.2 to 1.8 N·m)

6.3.2. Transmission cable

Shielded wire

(no

lm)

1-3/16 in. (30 mm)

1-3/8 in. (35 mm)

• Connect transmission cables as shown in Fig. B.
• When the 2 cables are attached.

Fig. B

GOOD

PROHIBITED

Different diameter

Connect to 1 side

WARNING

Tighten the terminal screws to the speci

ed torques, otherwise, abnormal overheating

may be produced and possibly cause heavy damage inside the unit.

Terminal number

Tightening torque

M3 screw

(Transmission/X1, X2)

4.4 to 5.3 Ibf·in

(0.5 to 0.6 N·m)

CAUTION

To peel the

lm from the lead cable, use a dedicated tool that will not damage the

conductor cable.

When installing a screw on the terminal block, do not cut the cable by overtightening
the screw. On the other hand, an under tightened screw can cause faulty contact,
which will lead to a communication failure.

Remove it with the following sequence in case of the state with the grille.

6.3.3. Remote controller cable

Remote controller cable modi

cation.

(1) Use a tool to cut off the terminal on the end of the remote controller cable, and then

remove the insulation from the cut end of the cable.

(2) Connect the remote control cable with connecting wire with solder.

Important : Be sure to insulate the connection between the cables.

Remote
controller
cable

25/32 in.

(20 mm)

White