background image

En-22

11. INFORMATION

Main contents of label

Item

Detail

  1. Model name

Model name

  2. Serial number

Serial number

  3. Electric characteristics

Phase, rated voltage, and frequency

  4. Weight 

Product weight

  5. Capacity

Cooling/heating capacity under cooling/
heating condition (refer to item 15)

  6. Current

Electric current during cooling/heating 
operation under cooling/heating condition 
(refer to item 15)

  7. Input power

Input during cooling/heating operation 
under cooling/heating condition (refer to 
item 15)

  8. Max. Current

Maximum electric current (temperature 
condition is max. cooling condition [refer 
to item 16])

  9. Air circulation

Air circulation

10. Noise level

Noise level

11. Refrigerant

Refrigerant type and initial charging 
amount

12. Max.  pressure  (HP/LP)

Means pressure of High Pressure side/
Low Pressure side

13. Protection

Protection  level against dust and water

14. Working temperature

Working temperature

15. Condition of cooling/heating

Dry-bulb temperature and wet-bulb tem-
perature under standard cooling/heating 
condition

16. Condition  of  max.  cooling

Dry-bulb temperature and wet-bulb tem-
perature at maximum electric current and 
input

17. Manufacture year

Manufacture year

18. Origin

Origin  country

19. Manufacturer

Manufacturer
FUJITSU GENERAL LIMITED 
Address: 1116, Suenaga, Takatsu-ku, 
Kawasaki 213-8502, Japan

9380545057_IM.indb   22

9380545057_IM.indb   22

2014/9/15   11:27:07

2014/9/15   11:27:07

Summary of Contents for AJY040LCLAH
























Reviews: