En-9
WARNING
When using solid core cables, do not use the ring terminal. If you use the solid core
cables with the ring terminal, the ring terminal’s pressure bonding may malfunction
and cause the cables to abnormally heat up.
B. For strand wiring
(1) Use ring terminals with insulating sleeves as shown in the
fi
gure below to connect to
the terminal block.
(2) Securely clamp the ring terminals to the cables using an appropriate tool so that the
cables do not come loose.
(3) Use the speci
fi
ed cables, connect them securely, and fasten them so that there is no
stress placed on the terminals.
(4) Use an appropriate screwdriver to tighten the terminal screws. Do not use a
screwdriver that is too small, otherwise, the screw heads may be damaged and
prevent the screws from being properly tightened.
(5) Do not tighten the terminal screws too much, otherwise, the screws may break.
(6) See the table for the terminal screw tightening torques.
(7) Please do not
fi
x 2 power supply cables with 1 screw.
Strip 3/8 in.
(10 mm)
Sleeve
Screw with
special washer
Screw with
special washer
Ring terminal
Cable
Cable
Terminal block
Ring terminal
Ring terminal
WARNING
Use ring terminals and tighten the terminal screws to the speci
fi
ed torques, otherwise,
abnormal overheating may be produced and possibly cause heavy damage inside the
unit.
Tightening torque
M4 screw
(Power supply/L1, L2 (N), GND)
11 to 16 lbf·in
(1.2 to 1.8 N·m)
6.3.2. Transmission and Remote controller cable
Shielded wire
(no
fi
lm)
1-3/16 in. (30 mm)
1-15/16 in. (50 mm)
Transmission cable
Remote controller cable
For 3-wire type
For 2-wire type
1-3/16 in. (30 mm)
1-3/16 in. (30 mm)
• When the 2 cables are attached:
GOOD
PROHIBITED
Different diameter
Connect to 1 side
WARNING
Tighten the terminal screws to the speci
fi
ed torques, otherwise, abnormal overheating
may be produced and possibly cause heavy damage inside the unit.
Tightening torque
M3 screw
(Transmission/X1, X2)
(Remote controller/Y1, Y2, Y3)
4.4 to 5.3 lbf·in
(0.5 to 0.6 N·m)
CAUTION
To peel the
fi
lm from the lead cable, use a dedicated tool that will not damage the
conductor cable.
When installing a screw on the terminal block, do not cut the cable by overtightening
the screw. On the other hand, an undertightened screw can cause faulty contact, which
will lead to a communication failure.
]1
6.4. Connection of wiring
(1) Remove the electric component box.
Electric component box
Electric component box
RFM
CAUTION
Do not remove the RFM
fi
xing screws. If the stays are removed, the electric component
box will fall.
If you use as “Floor console”, you must remove screws and RFMs (2 position).
When removing the electric component box, remove the clamp from the cables.
After completing the work, fasten the cables as they were originally by installing the clamp.
Cables
Clamp
Remove the clamp.
Install the clamp.
(2) Pull out the electric component box.
Electric component box
(3) Remove the electric component box cover.
Remove the 3 tapping screws.
Electric component box cover
Base
CAUTION
Be careful not to pinch the lead cables between the electric component box and
base.
9367701124-03_IM.indb Sec1:9
9367701124-03_IM.indb Sec1:9
2013-10-25 13:00:44
2013-10-25 13:00:44
