Airspan FlexNET ASN-700 User Manual Download Page 31

Page: 31 / 76

605-0001-801 FlexNET Link Products

HTTP

The HTTP service enables an administrator to connect to the ASN-700/800 configuration

system using a web browser.

HTTPS

The HTTPS service enables an administrator to establish an encrypted and secure HTTPS

connection (encrypted using SSL, Secured Sockets Layer) to the ASN-700/800

configuration system using a web browser.

WARNING! Under no circumstances should you disable all remote login services! At

least one remote login service should remain operational, to enable you to access and

configure the ASN-700/800.

Click the OK and Commit Settings buttons to retain any changes you make.

Configuring administrator accounts

Click on the SECURITY>Administrators link in the configuration menu to open the

Administrators configuration page.

The ASN-700/800 is shipped factory-set with the following single administrator account:

Username: admin

Password: default

It is strongly recommended that you change the factory-set password to one of your own as
soon as possible, in order to prevent unauthorized access to the configuration system of your

ASN-700/800 unit.

Note: When changing the password, the new password will also be your new SSH

password.

Figure 16

Editing administrator information

Summary of Contents for FlexNET ASN-700













































































Search results

Summary of Contents for FlexNET ASN-700

Reviews:

Related manuals for FlexNET ASN-700

Brands by name

Popular brands

Airspan FlexNET ASN-700, User Manual

Search results

Summary of Contents for FlexNET ASN-700

Reviews:

Related manuals for FlexNET ASN-700

Brands by name

Popular brands