Airspan FlexNET ASN-700 User Manual Download Page 10 | Manualshive

Page: 10 / 76

background image

605-0001-801 FlexNET Link Products

LED indicator

The LED indicator is also located on the bottom of the housing. The operation of the LED

indicator is as follows:

Reboot: flashing blue once per second

Committing configuration and initializing the radios: flashing blue twice per

second

Factory reset: solid red when erasing the configuration

Upgrade software: flashing red once per second

MAIN FUNCTIONALITIES

FlexNET link products are designed for wireless point-to-point and repeater applications. The

main purpose of the link products is to provide a secure and high capacity transmission for

backhaul and transit connections. The FlexNET link products operate on unlicensed frequency
bands, 5.470-5.725 and 5.725-5.850 GHz frequencies using OFDM radios based on adaptive

modulation scheme.

FlexNET link products offer versatile features for different deployment models. Link products can

be configured to operate either in a routed or bridged mode. Wireless bridging mode is very

important application area for these products. Routed link mode is supported in either static

routing mode, or dynamic routing mode based on OSPFv2 routing protocol. OSPF (Open
shortest path first) is widely used routing protocol, which allows links to be deployed to support

redundant back routes, load balancing, multiple paths to end connections and automatic re-

configuration in case of malfunctioning link unit with back-up route. OSPF supports also

advanced integration of wired/wireless connections, where operators’ network routing topology

can be maintained across wired/fibre/wireless connections.

The FlexNET link products are available with integrated and external antennas. FlexNET single
radio version (ASN-700) includes an integrated high gain antenna. FlexNET two radio version

(ASN-800) does not have an integrated antenna; it is used with external, flexibly scalable

antenna solutions.

4

«
...
8
9
10
11
12
...
»

Summary of Contents for FlexNET ASN-700













































































Reviews:

No comments

Related manuals for FlexNET ASN-700

8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink

Brand: Tyco Electronics Pages: 18

Brand: iDirect Pages: 60

Module NI PXI-8250

Brand: National Instruments Pages: 39

Brand: Ubee Pages: 9

Brand: Dahua Pages: 6

Brand: bintec elmeg Pages: 33

AirStation WHR-G300N

Brand: Hornington Pages: 6

Brand: Gbord Pages: 8

Brand: CyberTAN Pages: 67

Brand: WAGO Pages: 2

Brand: Nilox Pages: 66

Brand: TP-Link Pages: 37

Brand: Razer Pages: 17

Brand: Topcom Pages: 16

DynaGST/2402G GEP-33224T-1

Brand: UNICOM Pages: 17

Brand: Airvana Pages: 90

CentreCOM AT-3716XL

Brand: Allied Telesis Pages: 2

SmartNode 4634 Series

Brand: Patton electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands