manualshive.com logo in svg

Airspan AirHarmony-4400, Installation Manual

Share
Download
Airspan AirHarmony-4400 Installation Manual Download Page 42

AirHarmony-4400 (External Cavity Filters) Installation Guide 

UGD-D01186 

Airspan Commercial and Internal Use 

36 

 

3.

 

Drill a minimum 7/16” hole to accept the 3/8-16 threaded rod. 

4.

 

Thread the 3/8-16 threaded rod into the provided clinch-nut attached on the Pole/Wall 
mounting plate. 

5.

 

Holding the mounting plate (with the attached threaded rod) pass the 3/8-16 threaded rod 
through the drilled hole in the pole. 

6.

 

Install on the exposed thread that protrudes from pole a flat washer, split washer, and 
then a 3/8”-16 hex nut and tighten. 

7.

 

Insert the clamp bands by passing them through the slots in the mounting plate, in three 
(3) places. 

Note:

 The clamp bands are not supplied by Airspan and are the responsibility of the 

installer. Clamp bands should not be wider than 15.5 mm in order to fit in the slots on 
the mounting plate. 

 

8.

 

Tighten the clamp bands with large flat screwdriver. 

 

Figure 26: Mounting plate on pole 

 

 

 

 

Summary of Contents for AirHarmony-4400































































Reviews:

No comments

Brands by name

Popular brands

Load more brands