Airmar Technology Corporation TDT1000 Owner'S Manual Download Page 15

Page: 15 / 17

About Airmar’s SensorCheck

™

App

The SensorCheck app will interface with the TDT1000:

• To find the Airmar XducerID

feature if it is present.

• To identify a transducer with NO XducerID feature.
• To test a transducer’s characteristics.

- Acceptable minimum impedance range.
- Acceptable frequency range.

• To compare a transducer being tested to Factory Data.
• To judge a transducer as either

- “In Range”: The transducer is functioning properly.
- “Out of Range”: The transducer may not be functioning properly. Or there may be a problem

with the test set-up or the instrument. Do NOT remove/return the transducer. Contact your
customer service representative.

• To summarize information about a transducer and the vessel in which it is installed.
• To store test history.
• To share test results.

Download SensorCheck App

Airmar’s SensorCheck app can be installed on any wireless iOS or Android device.

1. Go to the Apple App Store or Google Play Store.
2. Search on the word Airmar.
3. Download the free SensorCheck app (Figures 9 and 10).

NOTE:

The SensorCheck app can be connected to only one TDT1000 at a time.

Figure 9. SensorCheck app icon

Figure 10. SensorCheck QR Code

Summary of Contents for TDT1000

















