AirLive WFP-101U User Manual Download Page 120

Page: 120 / 133

13.2 Enable MFP Server’s TCP/IP Support

The default configuration of the MFP Server is with TCP/IP support enabled.

Anyway, you can configure the MFP Server to enable TCP/IP support using

the configuration program.

13.3 Setup MFP Server’s IP Address

The MFP Server must have a unique IP address in order to be recognized by

the network.

You can set up the IP address on the various Unix systems using any one of

the following methods:

1. DHCP (Dynamic Host Configuration Protocol)

2. BOOTP (Bootstrap Protocol)

The MFP Server will use the last two methods to obtain its IP address

automatically if its IP address is configured as Auto (0.0.0.0).

13.3.1 DHCP

There are many Unix systems that support DHCP protocol, and the

procedures to configure the DHCP server database are different. Please refer

to the manual of Unix for the way to use different DHCP Server. It is highly

recommended that the DHCP server should be located on the same network

as the MFP Server.

113

AirLive WFP-101U User’s Manual

Summary of Contents for WFP-101U






































































































































Search results

Summary of Contents for WFP-101U

Reviews:

Related manuals for WFP-101U

Brands by name

Popular brands

AirLive WFP-101U, User Manual

Search results

Summary of Contents for WFP-101U

Reviews:

Related manuals for WFP-101U

Brands by name

Popular brands