manualshive.com logo in svg

AIREDALE AIR 1-550.30, Installation And Service Manual

Share
Download
AIREDALE AIR 1-550.30 Installation And Service Manual Download Page 7

AIR 1-550.30

OPERATION

7

Connections

 — Female-type permits direct connection of unit heater to the 

piping. WSC models have malleable connectors at side of the unit.

Vertical fins

 — Less opportunity for dust and dirt to collect. Reduces cleaning. 

Fins die-formed for added strength and heat transfer.

Coil

 — All air passes through coil. Heating is uniform. Design assures maximum 

control over air delivery and temperature of air leaving the heater. Aluminum 

fins die-formed for added strength — increased heat transfer. Fins mechanically 

bonded to serpentine copper tube.

Motor

 — All motors are totally enclosed. Single phase types include built-in 

thermal overload protection. All motor wiring is terminated in an electrical junction 

box either supplied on the unit heater or as an integral part of the motor.

Fan

 — Lightweight. Blades accurately balanced and pitched to move air quietly 

and positively — with minimum power requirement.

Safety fan guard

 — Standard equipment. Bolted steel rod fan guard completely 

surrounds the fan offering constant protection.

Deflector blades

 — Adjustable horizontal air-deflector blades are standard — 

vertical blades are optional. 

Casings

 — Electrostatically applied, gray-green polyester powder coat paint 

finish is applied over rust- and corrosion-treated steel for long life.

Motor-Cooling Cone

 — Shields   

motor from coil heat — prolongs life  

of insulation, windings, and lubricant. 

Prolongs motor life.

Coil

 — Aluminum fins mechanically 

bonded to tubes for maximum heat 

transfer. All steam- and water-

carrying passages between heavy 

steel pipe connections are copper, or 

cupronickel.

Motor

 — All motors are totally 

enclosed. Single phase types include 

built-in thermal overload protection. 

Fan

 — Accurately balanced to 

operate quietly and at lowest possible 

power consumption.

Junction Box

 — Easier installation 

with single point electrical connection.

Motor easily removable

 — Modine 

design permits motor to be removed 

through opening below the unit — 

especially important where heaters are 

installed close to ceiling.

Vertical fins

 — Less opportunity for 

dust and dirt to collect. Exposed for 

easy cleaning with air hose and brush.

Casings

 — Electrostatically applied, 

gray-green polyester powder coat paint 

finish applied over rust- and corrosion-

treated steel lasts longer.

Figure 7.1 - Horizontal Delivery Unit Cutaway

Figure 7.4 - Vertical Delivery Unit Cutaway

Figure 7.2 - Typical Horizontal Unit with Standard 

Junction Box

Figure 7.3 - Horizontal Unit with Optional  

Fingerproof Fan Guard

Summary of Contents for AIR 1-550.30

















Reviews:

No comments

Brands by name

Popular brands

Load more brands