manualshive.com logo in svg

Air Live FE-501OD, User Manual

Share
Download
Air Live FE-501OD User Manual Download Page 7

1. Overview 

AirLive FE-501OD User’s Manual

 

3 

Pan/Tilt/Zoom 

ePTZ:10x digital zoom 

On-board Storage 

Built-in MicroSD card slot, support SDHC/SDXC 64GB or 
above 

Video

 

Compression 

H.264, MJPEG & MPEG-4 

Display Mode 

360° Source View, 360° Broad View,   
180° Double Broad View, Triple View, Quad View,   
3 PTZ with Source View 

Maximum Frame Rate 

15fps@1920x1920 
15fps@1920x1080 
30fps@1600x1200(HI-FPS Mode) 
30fps@640x480 

Maximum Streams 

5 simultaneous streams at ROI Mode 
3 simultaneous streams at Normal Mode 

S/N Ratio 

Above 39 dB 

Dynamic Range 

100 dB 

Video Streaming 

Adjustable resolution, quality and bitrate 
ROI(Region of Interest) Provide for 5 Independent Streams

Image Settings 

Adjustable image size, quality and bitrate 
Configurable brightness, saturation, exposure control, 
sharpness, contrast, white balance, auto shutter control, 
auto gain control, noise reduction, EV luminance control, 
flip & mirror, privacy masks, time stamp, text overlay   

Audio

 

Audio Capability 

Audio input/output (full duplex) 

Compression 

G.711u 

Interface 

External microphone input   

Effective Range 

5 meters 

Network

 

Users 

Live view for up to 10 clients 

Protocols 

HTTP, HTTPS, TCP/IP, IPv4, UDP, SMTP, FTP, DHCP, 
DDNS, NTP, DNS, ARP, RTSP, RTP, UPnP, OnVIF(Profile 
S), Multicast

 

Interface 

10 Base-T/100 Base TX Ethernet(RJ-45) 

OnVIF 

Ver.2.2 

Intelligent Video

 

Motion Detection 

Ten-window video motion detection 

Summary of Contents for FE-501OD





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands