background image

 

6) 

If the plug or outlet does get wet DO NOT UNPLUG THE CORD; Disconnect the fuse or 
circuit breaker supplying power to the pump, then unplug and examine for the presence of 
water in the outlet. 

7) 

DO NOT use the pump near volatile liquids such as gasoline, thinners, etc,. as this creates 
the possibility of an explosion. 

 

CAUTIONS FOR USE 

1) 

Close supervision is necessary when an air pump is used by or near children. 

2) 

This pump is intended for 

clean, dry air only

. DO NOT, under any circumstances, attempt 

operation with water or other liquids, otherwise pump may be damaged. 

3) 

The ambient operating temperature for this pump is between 41

(5

) and 104

(40

). 

Operation of pump in temperatures outside the recommended temperature range may result 
in malfunction or severely shortened service life. 

4) 

DO NOT block the air from being discharged. Air pumps must have sufficient room to allow 
for heat dissipation.   

5) 

Failure to observe cautions will cause the pump to automatically switch off until cool.   

 

 

 
 

6) 

Always unplug pump prior to servicing. Grasp plug to remove cord from outlet. DO NOT 
remove by pulling on power cord. 

7) 

DO NOT use the air pump for other than  its  intended use. The use of attachments not 
recommended or not sold by Sunlight Supply, Inc may cause an unsafe condition. 

8) 

DO NOT install pump where it will be exposed to weather. 

9) 

DO NOT store pump in temperatures below freezing. 

10) 

Ensure pump is securely mounted prior to operation. 

11) 

Read and observe all important markings on pump. 

12) 

Ensure that extension cords (if required) have the correct or higher rating (amperes or watts). 
Ensure cord is properly positioned to avoid tripping.

 

13) 

To avoid injury, DO NOT contact moving parts or hot parts. 

14) 

Always  unplug an appliance from an outlet  before  putting on or taking off parts,before 
cleaning and when not in use

 

 
 

DO NOT REMOVE PUMP CASING UNLESS UNIT IS DISCONNECTED 

FROM MAIN POWER SUPPLY. 

 

3

Summary of Contents for 15

















Reviews: