background image

 

WARNING 

 

 IMPORTANT SAFEGUARDS

READ AND FOLLOW ALL SAFETY 

INSTRUCTIONS 

 TO REPLACE OR CHANGE ANY OF THE PARTS REFERRED IN THE 

SERVICE MANUAL, WE STRONGLY RECOMMEND YOU CONTACT AN 
AUTHORIZED TECHNICIAN. 

 

 

 

 

 

 

 

 
 
DANGER 

--

To avoid possible electric shock, special care should be taken 

since water is used with or near aquariums and reservoirs. For each of the 
following situations DO NOT attempt repairs yourself, instead return the air 
pump to the retailer where you purchased the pump  for servicing  or 
discarding of the pump

.

 

Precautions for pump use: 

 

1) 

If the pump falls into the water, DO NOT

 

REACH FOR IT. First unplug the pump and then 

retrieve it. If the pump’s electrical components get wet, unplug the pump immediately. 

2) 

Carefully examine the air pump after installation. It should NOT be plugged in if there is water 
present on any of the pumps parts. 

3) 

DO NOT operate if the cord or plug is damaged. 

4) 

DO NOT operate if the pump is malfunctioning, dropped, or damaged in any way. 

5) 

To prevent the plug or electrical outlet  from  getting wet, position the  aquarium  tank  or 
reservoir stand to one side of a wall mounted outlet. A “drip loop” shown in the figure above, 
should be arranged for each cord connecting an air pump to an electrical outlet. The “drip 
loop” is the part of the cord below the level of the outlet or connector if an extension cord is 
used. The “drip loop” prevents water from traveling along the cord from coming into contact 
with the outlet.   
 

2

Summary of Contents for 15

















Reviews: