Air Design PREMA Series Installation & Maintenance Instructions Manual Download Page 24

Page: 24 / 36

INSTALLATION & MAINTENANCE INSTRUCTIONS

PREMA

CEILING VOID ENERGY RECOVERY VENTILATION UNITS

Installation - Wiring

All units are Single Phase 220V to 240V 50/60Hz. Mains must
be wired directly into the 2P Single Phase Isolator. Mains is factory
wired between the isolator and the main control box.

PREMA180

The control box is mounted on the outside of the unit.

PREMA330, PREMA540 and PREMA900

The control box is mounted behind the supply fan panel.

Remove to access

There are four pre-configured entry locations on the control box for external wiring entry.
The Single Phase 220V to 240V 50/60Hz mains from the isolator is factory wired.

The three remaining locations are used for:
1)

Controller display

Filter indication

A N Other (BMS, external sensor etc.)

IP rated cable glands are supplied, bagged inside the control box.

Installation, Operating & Maintenance

PERMA

INSTALLATION - WIRING

All units are Single Phase 220V to 240V 50/60Hz. Mains must be wired directly into the 2P Single Phase

Isolator. Mains is factory wired between the ISOLATOR and the main CONTROL BOX.

PREMA180

The control box is mounted on

the outside of the unit.

PREMA330, 540 and 900

The Control Box is mounted behind the Supply fan panel

(Remove to access)

There are Four (4) pre-configured entry locations on the control box for external wiring entry.

The Single Phase 220V to 240V 50/60Hz mains from the Isolator is factory wired.

The Three(3) remaining locations are used for

1) Controller display

2) Filter indication

3) A N Other (BMS, external sensor etc)

IP rated cable glands are supplied, bagged inside the control box

Installation, Operating & Maintenance

PERMA

INSTALLATION - WIRING

All units are Single Phase 220V to 240V 50/60Hz. Mains must be wired directly into the 2P Single Phase

Isolator. Mains is factory wired between the ISOLATOR and the main CONTROL BOX.

PREMA180

The control box is mounted on

the outside of the unit.

PREMA330, 540 and 900

The Control Box is mounted behind the Supply fan panel

(Remove to access)

There are Four (4) pre-configured entry locations on the control box for external wiring entry.

The Single Phase 220V to 240V 50/60Hz mains from the Isolator is factory wired.

The Three(3) remaining locations are used for

1) Controller display

2) Filter indication

3) A N Other (BMS, external sensor etc)

IP rated cable glands are supplied, bagged inside the control box

Installation, Operating & Maintenance

PERMA

INSTALLATION - WIRING

All units are Single Phase 220V to 240V 50/60Hz. Mains must be wired directly into the 2P Single Phase

Isolator. Mains is factory wired between the ISOLATOR and the main CONTROL BOX.

PREMA180

The control box is mounted on

the outside of the unit.

PREMA330, 540 and 900

The Control Box is mounted behind the Supply fan panel

(Remove to access)

There are Four (4) pre-configured entry locations on the control box for external wiring entry.

The Single Phase 220V to 240V 50/60Hz mains from the Isolator is factory wired.

The Three(3) remaining locations are used for

1) Controller display

2) Filter indication

3) A N Other (BMS, external sensor etc)

IP rated cable glands are supplied, bagged inside the control box

Summary of Contents for PREMA Series





































Search results

Summary of Contents for PREMA Series

Reviews:

Related manuals for PREMA Series

Brands by name

Popular brands

Air Design PREMA Series, Installation & Maintenance Instructions Manual

Search results

Summary of Contents for PREMA Series

Reviews:

Related manuals for PREMA Series

Brands by name

Popular brands